Fracture properties of alkali-activated slag and ordinary Portland cement concrete and mortar

Abstract Three-point bending (TPB) tests were conducted on notched beams to compare the fracture properties of alkali-activated slag (AAS) concrete and ordinary Portland cement (OPC) concrete at three different compressive strength levels (30, 50 and 70 MPa). Parallel comparisons were also conducted between AAS mortar (AASM) and OPC mortar (OPCM). Load vs. mid-span deflection (P-δ) curves, load vs. crack mouth opening displacement (P-CMOD) curves and load vs. crack tip opening displacement (P-CTOD) curves of the tested beams were obtained. The fracture energy GF and the characteristic length (lch) of the AAS and OPC concrete and mortar were calculated and analyzed. It was found that the GF of AAS concrete was always higher than that of OPC concrete given the same compressive strength, due to their denser and stronger interfacial transition zones (ITZs). At a compressive strength of 30 MPa, the GF of AASM was also larger than its OPC counterparts. However, the GF of AASM became lower than that of OPCM when the compressive strengths were 50 and 70 MPa, as more initial micro-cracks were formed in the AASM matrix with strength increase. In addition, the lch values of AAS concrete and mortar were all smaller than those of OPC, implying that the formers were more brittle given the same compressive strengths. The elastic modulus of AAS concrete and mortar were found to be always lower than those of OPC. Micro-structural observations were carried out to explain the above phenomena.

[1]  P. Sarker,et al.  Fracture behaviour of heat cured fly ash based geopolymer concrete , 2013 .

[2]  P. Ogrodnik,et al.  Ultra-high strength concrete made with recycled aggregate from sanitary ceramic wastes – The method of production and the interfacial transition zone , 2016 .

[3]  J. Sanjayan,et al.  Workability and mechanical properties of alkali activated slag concrete , 1999 .

[4]  B. H. Bharatkumar,et al.  Effect of fly ash and slag on the fracture characteristics of high performance concrete , 2005 .

[5]  Jaime Planas,et al.  The effect of the bond between the matrix and the aggregates on the cracking mechanism and fracture parameters of concrete , 2002 .

[6]  S. Shah,et al.  Characterization of the paste-aggregate interfacial transition zone surface roughness and its relationship to the fracture toughness of concrete , 1995 .

[7]  M. .. S. D. Rojas,et al.  Properties of interfacial transition zones (ITZs) in concrete containing recycled mixed aggregate , 2017 .

[8]  Frank Collins,et al.  Effect of pore size distribution on drying shrinkage of alkali-activated slag concrete , 2000 .

[9]  P. L. Pratt,et al.  Alkali-activated slag cement and concrete: a review of properties and problems , 1995 .

[10]  Jay G. Sanjayan,et al.  Fracture properties of geopolymer paste and concrete , 2011 .

[11]  Z. Bažant,et al.  Crack band theory for fracture of concrete , 1983 .

[12]  A. Hillerborg.  The theoretical basis of a method to determine the fracture energyGF of concrete , 1985 .

[13]  T I Milne,et al.  INFLUENCE OF CEMENT BLEND AND AGGREGATE TYPE ON STRESS-STRAIN BEHAVIOR AND ELASTIC MODULUS OF CONCRETE , 1995 .

[14]  C. Shi,et al.  Selectivity of Alkaline Activators for the Activation of Slags , 1996 .

[15]  Cengiz Duran Atiş,et al.  Influence of Activator on the Strength and Drying Shrinkage of Alkali-Activated Slag Mortar , 2009 .

[16]  Surendra P. Shah,et al.  Two Parameter Fracture Model for Concrete , 1985 .

[17]  Anja Buchwald,et al.  Life-cycle analysis of geopolymers , 2009 .

[18]  J. Dai,et al.  Mechanical properties of alkali-activated concrete: A state-of-the-art review , 2016 .

[19]  Zhiliang Zhang,et al.  Effect of silica fume, steel fiber and ITZ on the strength and fracture behavior of mortar , 2009 .

[20]  R. Cloots,et al.  (Micro)-structural comparison between geopolymers, alkali-activated slag cement and Portland cement , 2006 .

[21]  Ángel Palomo,et al.  Composition and Microstructure of Alkali Activated Fly Ash Binder: Effect of the Activator , 2005 .

[22]  Z. Bažant.  Size Effect in Blunt Fracture: Concrete, Rock, Metal , 1984 .

[23]  A. Hillerborg,et al.  Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements , 1976 .

[24]  Shao-dong Wang.  Alkaline activation of slag , 1995 .

[25]  Serdar Aydın,et al.  Effect of activator type and content on properties of alkali-activated slag mortars , 2014 .

[26]  R. H. Atkinson.  Recent advances in the applied chemistry of the rare metals. Jubilee memorial lecture , 1940 .

[27]  Frank Winnefeld,et al.  Hydration of alkali-activated slag: comparison with ordinary Portland cement , 2006 .

[28]  Jay G. Sanjayan,et al.  Alkali activation of Australian slag cements , 1999 .

[29]  S. Siddique,et al.  Lateral force microscopic examination of interfacial transition zone in ceramic concrete , 2017 .

[30]  S. Mindess,et al.  Microhardness testing of cementitious materials , 1996 .

[31]  C. Shi,et al.  Alkali-Activated Cements and Concretes , 2003 .

[32]  Liangcai Cai,et al.  Fracture properties and response surface methodology model of alkali-slag concrete under freeze–thaw cycles , 2015 .

[33]  Caijun Shi,et al.  Interface between cement paste and quartz sand in alkali-activated slag mortars , 1998 .

[34]  Zhou-Dao Lu,et al.  Determining residual double-K fracture toughness of post-fire concrete using analytical and weight function method , 2014 .

[35]  D. Roy.  Alkali-activated cements Opportunities and challenges , 1999 .

[36]  Jiangtao Yu,et al.  Determination of the softening curve and fracture toughness of high-strength concrete exposed to high temperature , 2015 .

[37]  J. Gillott,et al.  Mechanism of alkali-silica reaction and the significance of calcium hydroxide , 1991 .

[38]  J. Deventer,et al.  The Role of Inorganic Polymer Technology in the Development of ‘Green Concrete’ , 2007 .

[39]  A. Atkinson,et al.  Sodium silicate-based, alkali-activated slag mortars: Part I. Strength, hydration and microstructure , 2002 .

[40]  J. Dai,et al.  Effects of nano-TiO2 on strength, shrinkage and microstructure of alkali activated slag pastes , 2015 .