Low-Temperature Two-Phase Microchannel Cooling for High-Heat-Flux Thermal Management of Defense Electronics

For a given heat sink thermal resistance and ambient temperature, the temperature of an electronic device rises fairly linearly with increasing device heat flux. This relationship is especially problematic for defense electronics, where heat dissipation is projected to exceed 1000 W/cm2 in the near future. Direct and indirect low-temperature refrigeration cooling facilitate appreciable reduction in the temperature of both coolant and device. This paper explores the benefits of cooling the device using direct and indirect refrigeration cooling systems. In the direct cooling system, a microchannel heat sink serves as an evaporator in a conventional vapor compression cycle using R134a as working fluid. In the indirect cooling system, HFE 7100 is used to cool the heat sink in a primary pumped liquid loop that rejects heat to a secondary refrigeration loop. Two drastically different flow behaviors are observed in these systems. Because of compressor performance constraints, mostly high void fraction two-phase patterns are encountered in the R134a system, dominated by saturated boiling. On the other hand, the indirect refrigeration cooling system facilitates highly subcooled boiling inside the heat sink. Both systems are shown to provide important cooling benefits, but the indirect cooling system is far more effective at dissipating high heat fluxes. Tests with this system yielded cooling heat fluxes as high as 840 W/cm2 without incurring critical heat flux (CHF). Results from both systems are combined to construct an overall map of performance trends relative to mass velocity, subcooling, pressure, and surface tension. Extreme conditions of near-saturated flow, low mass velocity, and low pressure produce ldquomicrordquo behavior, where macrochannel flow pattern maps simply fail to apply, instabilities are prominent, and CHF is quite low. One the other hand, systems with high mass velocity, high subcooling, and high pressure are far more stable and yield very high CHF values; two-phase flow in these systems follows the fluid flow and heat transfer behavior as well as the flow pattern maps of macrochannels.

[1]  T. Hibiki,et al.  Some characteristics of air-water two-phase flow in small diameter vertical tubes , 1996 .

[2]  I. Mudawar,et al.  Flow boiling heat transfer in two-phase micro-channel heat sinks––I. Experimental investigation and assessment of correlation methods , 2003 .

[3]  Victor Chiriac,et al.  The Miniaturization of a Refrigeration Vapor Compression System and Application to the Cooling of High Power Microelectronics , 2006 .

[4]  Patrick E. Phelan,et al.  Current and future miniature refrigeration cooling technologies for high power microelectronics , 2002 .

[5]  Roger R. Schmidt,et al.  High-end server low-temperature cooling , 2002, IBM J. Res. Dev..

[6]  I. Mudawar,et al.  Two-phase flow in high-heat-flux microchannel heat sink for refrigeration cooling applications : Part I – – pressure drop characteristics , 2005 .

[7]  I. Mudawar,et al.  Ultra-high critical heat flux (CHF) for subcooled water flow boiling—I: CHF data and parametric effects for small diameter tubes , 1999 .

[8]  I. Mudawar,et al.  Measurement and prediction of pressure drop in two-phase micro-channel heat sinks , 2003 .

[9]  A. Kawahara,et al.  Investigation of two-phase flow pattern, void fraction and pressure drop in a microchannel , 2002 .

[10]  I. Mudawar,et al.  Fluid flow and heat transfer characteristics of low temperature two-phase micro-channel heat sinks – Part 1: Experimental methods and flow visualization results , 2008 .

[11]  A. Abdel-azim.  Fundamentals of Heat and Mass Transfer , 2011 .

[12]  M. W. Wambsganss,et al.  Two-phase pressure drop of refrigerants during flow boiling in small channels : an experimental investigation and correlation development. , 1999 .

[13]  H. Lee,et al.  Pressure drop correlations for two-phase flow within horizontal rectangular channels with small heights , 2001 .

[14]  I. Mudawar,et al.  Two-phase flow in high-heat-flux micro-channel heat sink for refrigeration cooling applications: Part II—heat transfer characteristics , 2005 .

[15]  Andrei G. Fedorov,et al.  Experimental Investigation of Compact Evaporators for Ultralow Temperature Refrigeration of Microprocessors , 2007 .

[16]  R. Kirschman,et al.  Cold electronics: An overview , 1984 .

[17]  R. Webb,et al.  Correlation of two-phase friction for refrigerants in small-diameter tubes , 2001 .

[18]  I. Mudawar,et al.  Fluid flow and heat transfer characteristics of low temperature two-phase micro-channel heat sinks – Part 2. Subcooled boiling pressure drop and heat transfer , 2008 .

[19]  Issam Mudawar,et al.  Implementation of Microchannel Evaporator for High-Heat-Flux Refrigeration Cooling Applications , 2006 .

[20]  Issam Mudawar.  Assessment of high-heat-flux thermal management schemes , 2001 .

[21]  Issam Mudawar,et al.  Two-Phase Electronic Cooling Using Mini-Channel and Micro-Channel Heat Sinks: Part 1—Design Criteria and Heat Diffusion Constraints , 1994 .

[22]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[23]  M. Nisenoff,et al.  Low Temperature Electronics workshop , 2000, Sixteenth Annual IEEE Semiconductor Thermal Measurement and Management Symposium (Cat. No.00CH37068).

[24]  M. A. El-Masri,et al.  Boiling heat transfer and critical heat flux in high-speed rotating liquid films , 1985 .

[25]  I. Mudawar,et al.  Two-Phase Electronic Cooling Using Mini-Channel and Micro-Channel Heat Sinks: Part 2—Flow Rate and Pressure Drop Constraints , 1994 .

[26]  Issam Mudawar,et al.  High flux boiling in low flow rate, low pressure drop mini-channel and micro-channel heat sinks , 1994 .

[27]  Said I. Abdel-Khalik,et al.  Gas–liquid two-phase flow in microchannels: Part II: void fraction and pressure drop , 1999 .

[28]  I. Mudawar,et al.  Flow boiling heat transfer in two-phase micro-channel heat sinks--II. Annular two-phase flow model , 2003 .