Comparison of magnetic Barkhausen noise and ultrasonic velocity measurements for microstructure evaluation of SAE 1040 and SAE 4140 steels

Abstract The aim of this study is to compare the performance of magnetic Barkhausen noise and ultrasonic methods for the evaluation of the microstructure of commercial steels. Following the austenitization of the specimens made of SAE 1040 and SAE 4140, various heat treatments were carried out to obtain microstructures consisting of martensite, tempered martensite, fine pearlite–ferrite, and coarse pearlite–ferrite. The microstructures were initially characterized by SEM investigation and hardness measurements. The magnitude and position of Barkhausen noise peaks were determined via a commercial system. The propagation rates of longitudinal waves were determined with the ultrasonic pulse-echo technique. Barkhausen noise response and sound velocity goes to minimum for the as-quenched martensite, and both tend to increase in the following sequence: tempered martensite, fine pearlite–ferrite, and coarse pearlite–ferrite. However, the magnetic features are more sensitive to the microstructure variations than to the sound velocity.

[1]  Yasubumi Furuya,et al.  The effect of grain boundary microstructure on Barkhausen noise in ferromagnetic materials , 2001 .

[2]  R. Fougères,et al.  Characterization of pure iron and (130 p.p.m.) carbon–iron binary alloy by Barkhausen noise measurements: study of the influence of stress and microstructure , 1998 .

[3]  T. Jayakumar,et al.  Insight into the microstructural characterization of ferritic steels using micromagnetic parameters , 2000 .

[4]  E. Papadakis.  Ultrasonic attenuation and velocity in SAE 52100 steel quenched from various temperatures , 1970, Metallurgical and Materials Transactions B.

[5]  D. Jiles,et al.  Influence of microstructure on micromagnetic Barkhausen emissions in AISI 4140 steel , 1995 .

[6]  David L. Atherton,et al.  Influence of magnetizing parameters on the magnetic Barkhausen noise , 1992 .

[7]  William Shockley,et al.  Magnetic Domain Patterns on Single Crystals of Silicon Iron , 1949 .

[8]  D. Atherton,et al.  The influence of pearlite on barkhausen noise generation in plain carbon steels , 1991 .

[9]  K. M. Koo,et al.  Characterization of pearlite grains in plain carbon steel by Barkhausen emission , 2002 .

[10]  J. Chicois,et al.  Barkhausen noise from plain carbon steels: analysis of the influence of microstructure , 1999 .

[11]  Linilson R. Padovese,et al.  Magnetic Barkhausen Noise and hysteresis loop in commercial carbon steel : influence of applied tensile stress and grain size , 2001 .

[12]  I. Mészáros,et al.  Barkhausen Noise Energy Measurement Method for Characterizing the Ferromagnetic Ratio of Alloys , 1996 .

[13]  P. Srivastava,et al.  Ferromagnetic properties of deformation-induced martensite transformation in AISI 304 stainless steel , 2004 .

[14]  Baldev Raj,et al.  Ultrasonic velocity measurements for characterizing the annealing behaviour of cold worked austenitic stainless steel , 2000 .

[15]  C. Gur,et al.  Ultrasonic characterisation of hot-rolled and heat-treated plain carbon steels , 2003 .

[16]  Ultrasonic characterization of materials hardness , 2000, Ultrasonics.

[17]  D. Jiles,et al.  BARKHAUSEN EFFECT IN STEELS AND ITS DEPENDENCE ON SURFACE CONDITION , 1997 .

[18]  Barkhausen effect in ground steels , 1997 .

[19]  V. Moorthy,et al.  Evaluation of tempering induced changes in the hardness profile of case-carburised EN36 steel using magnetic Barkhausen noise analysis , 2003 .

[20]  X. Kleber,et al.  Ferrite-martensite steels characterization using magnetic Barkhausen noise measurements , 2004 .

[21]  C. Gür,et al.  Characterization of microstructural phases of steels by sound velocity measurement , 2005 .

[22]  Study of the influence of deformation and thermal treatment on the ultrasonic behaviour of steel , 1994 .

[23]  High-voltage Lorentz electron microscopy studies of domain structures and magnetization processes in pearlitic steels , 1987 .