A low-cost infrared sensing system for monitoring the MIG welding process

In this study, a low-cost infrared sensing system based on the analysis of the surface temperature distribution is proposed for monitoring the perturbations occurring during the aluminum alloy metal inert gas (MIG) welding process. A galvanometer scanner is employed in this real-time infrared sensing system to continually reflect the infrared energy to the point infrared sensor. By controlling the scanning mirror of the galvanometer scanner rotating in a high speed, the infrared energy at different points of the welding seam and the heat-affected zone on the surface of the plate will be continually captured by the point infrared sensor. Different conditions (changes in the welding speed, welding current, and joint gap width) of the welding process have been simulated to perturb the welding process. Three representative geometric defects such as undercut, humping, and lack of fusion were produced to validate our infrared sensing system. Experimental results showed that the sensing system is useful for monitoring perturbations that arise during the welding process and identifying welding defects.

[1]  Giovanni Celano,et al.  Monitoring the coefficient of variation using a variable sample size control chart in short production runs , 2015, The International Journal of Advanced Manufacturing Technology.

[2]  A. K. Bhaduri,et al.  Real-Time Monitoring of Weld Pool during GTAW using Infra-Red Thermography and analysis of Infra-Red thermal images , 2011 .

[3]  H. G. Fjaer,et al.  Modeling of microstructure evolution, residual stresses and distortions in 6082-T6 aluminum weldments , 1998 .

[4]  E. Pezzuti,et al.  Microstructural and mechanical characteristics of welded joints in type 6082-T6 aluminium alloy , 1997 .

[5]  Bryan A. Chin,et al.  Low-cost infrared sensing system for monitoring the welding process in the presence of plate inclination angle , 2003 .

[6]  Amin Al-Habaibeh,et al.  An autonomous low-Cost infrared system for the on-line monitoring of manufacturing processes using novelty detection , 2003 .

[7]  R. J. Ditchburn,et al.  NDT of welds: state of the art , 1996 .

[8]  Y. Fuh,et al.  Effect of welding sequence of a multi-pass temper bead in gas-shielded flux-cored arc welding process: hardness, microstructure, and impact toughness analysis , 2015 .

[9]  Shaojie Wu,et al.  A preliminary test of a novel molten metal filler welding process , 2015 .

[10]  A. K. Mondal,et al.  Overview of NDT methods applied on an aero engine turbine rotor blade , 2013 .

[11]  Álisson Rocha Machado,et al.  Machining of aluminum alloys: a review , 2016 .

[12]  K. Easterling.  Introduction to the physical metallurgy of welding , 1983 .

[13]  Nikhil R. Pal,et al.  Artificial neural network approach for estimating weld bead width and depth of penetration from infrared thermal image of weld pool , 2008 .

[14]  Kamal Pal,et al.  Multisensor-based monitoring of weld deposition and plate distortion for various torch angles in pulsed MIG welding , 2010 .

[15]  Xiangdong Gao,et al.  Laser-induced infrared characteristic analysis for evaluating joint deviation during austenitic stainless steel laser welding , 2017 .

[16]  T. Jayakumar,et al.  Intelligent modeling for estimating weld bead width and depth of penetration from infra-red thermal images of the weld pool , 2015, J. Intell. Manuf..

[17]  Baldev Raj,et al.  Estimating bead width and depth of penetration during welding by infrared thermal imaging , 2005 .

[18]  Bryan A. Chin,et al.  Infrared sensing techniques for penetration depth control of the submerged arc welding process , 2001 .

[19]  Charalabos C. Doumanidis,et al.  Multivariable Adaptive Control of Thermal Properties During Welding , 1991 .

[20]  Chien-Yi Huang,et al.  Innovative parametric design for environmentally conscious adhesive dispensing process , 2015, J. Intell. Manuf..

[21]  Luc Paradis,et al.  Modeling tools for ultrasonic inspection of welds , 2000 .

[22]  Gürel Çam,et al.  Recent developments in joining of aluminum alloys , 2017 .

[23]  Marvin Trimm,et al.  An overview of nondestructive evaluation methods , 2003 .

[24]  Sadek Crisóstomo Absi Alfaro,et al.  Characterization of “Humping” in the GTA welding process using infrared images , 2015 .