Design of FRC tunnel segments considering the ductility requirements of the Model Code 2010

Abstract Fibre reinforced concrete (FRC) is used to improve the mechanical response of precast segments for tunnels. The structural use of the material has been regulated by national codes and, recently, by the Model Code 2010 (MC 2010, hereinafter). In this regard, it is necessary to update the philosophy applied to the design of tunnel segments in compliance with the most recent guidelines, evaluating their applicability and repercussion. The objective of this paper is to present a critical analysis of the design of FRC segments according to the ductility requirements from the MC 2010; an alternative approach is proposed that is compatible with the condition found in some tunnels. The repercussions of both approaches are evaluated for the Metro Line 9 from Barcelona using results obtained in an experimental program with full-scale segments. The study suggests that the alternative approach may be applied under certain conditions, leading to a reduction in the fibre consumption.

[1]  C.B.M. Blom,et al.  Design philosophy of concrete linings for tunnels in soft soils , 2002 .

[2]  Antonio Aguado,et al.  Application of constitutive models in European codes to RC–FRC , 2013 .

[3]  Climent Molins,et al.  Experimental and analytical study of the structural response of segmental tunnel linings based on an in situ loading test. , 2011 .

[4]  Antonio Aguado,et al.  Packer behavior under simple and coupled stresses , 2012 .

[5]  Giovanni Plizzari,et al.  Structural behavior of precast tunnel segments under TBM thrust actions , 2014 .

[6]  M. Bakhshi,et al.  Developments in design for fibre-reinforced concrete tunnel segments , 2017 .

[7]  Bernardino Chiaia,et al.  Combining fiber-reinforced concrete with traditional reinforcement in tunnel linings , 2009 .

[8]  Climent Molins,et al.  Experimental and analytical study of the structural response of segmental tunnel linings based on an in situ loading test. Part 2: Numerical simulation , 2011 .

[9]  Antonio Aguado,et al.  Assessment of the fibre orientation factor in SFRC slabs , 2015 .

[10]  Antonio Aguado,et al.  Fibre distribution in macro-plastic fibre reinforced concrete slab-panels , 2014 .

[11]  A. G. Kooiman,et al.  Modelling Steel Fibre Reinforced Concrete for Structural Design , 2000 .

[12]  F Toutlemonde,et al.  5570 - ON THE DESIGN OF STEEL FIBER REINFORCED CONCRETE TUNNEL LINING SEGMENTS , 2013 .

[13]  Joaquim A. O. Barros,et al.  Post-cracking behaviour of steel fibre reinforced concrete , 2003 .

[14]  Zila Rinaldi,et al.  Design according to MC2010 of a fibre‐reinforced concrete tunnel in Monte Lirio, Panama , 2012 .

[15]  Joost C. Walraven,et al.  Formation and accumulation of contact deficiencies in a tunnel segmented lining , 2012 .

[16]  Carles Camós Andreu,et al.  An attempt to the determination of the partial safety factor for SFRC members subjected to bending forces , 2012 .

[17]  Franco Levi.  On Minimum Reinforcement in Concrete Structures , 1985 .

[18]  Bernardino Chiaia,et al.  Evaluation of crack width in FRC structures and application to tunnel linings , 2009 .

[19]  M. Bakhshi,et al.  Practical aspects of segmental tunnel lining design , 2013 .

[20]  J. C. Walraven,et al.  Structural behaviour of SFRC tunnel segments during TBM operations , 2007 .

[21]  Antonio Aguado,et al.  Multidirectional double punch test to assess the post-cracking behaviour and fibre orientation of FRC , 2014 .

[22]  Lucie Vandewalle,et al.  Fibre reinforced concrete: new design perspectives , 2009 .

[23]  Aurelio Muttoni,et al.  Fédération Internationale du Béton (fib), Model Code 2010 - First complete draft, chapters 7.3 and 7.13 , 2010 .

[24]  Bernardino Chiaia,et al.  Evaluation of minimum reinforcement ratio in FRC members and application to tunnel linings , 2007 .

[25]  Joost C. Walraven,et al.  High performance fiber reinforced concrete: progress in knowledge and design codes , 2009 .

[26]  Albert de la Fuente,et al.  Experiences in Barcelona with the use of fibres in segmental linings , 2012 .

[27]  Joost C. Walraven,et al.  New Design Method for the Production Tolerances of Concrete Tunnel Segments , 2012 .