Compact Electrothermal Reliability Modeling and Experimental Characterization of Bipolar Latchup in SiC and CoolMOS Power MOSFETs

In this paper, a compact dynamic and fully coupled electrothermal model for parasitic BJT latchup is presented and validated by measurements. The model can be used to enhance the reliability of the latest generation of commercially available power devices. BJT latchup can be triggered by body-diode reverse-recovery hard commutation with high dV/dt or from avalanche conduction during unclamped inductive switching. In the case of body-diode reverse recovery, the base current that initiates BJT latchup is calculated from the solution of the ambipolar diffusion equation describing the minority carrier distribution in the antiparallel p-i-n body diode. For hard commutation with high dV/dt, the displacement current of the drain-body charging capacitance is critical for BJT latchup, whereas for avalanche conduction, the base current is calculated from impact ionization. The parasitic BJT is implemented in Simulink using the Ebers-Moll model and the temperature is calculated using a thermal network matched to the transient thermal impedance characteristic of the devices. This model has been applied to CoolMOS and SiC MOSFETs. Measurements show that the model correctly predicts BJT latchup during reverse recovery as a function of forward-current density and temperature. The model presented, when calibrated correctly by device manufacturers and applications engineers, is capable of benchmarking the robustness of power MOSFETs.

[1]  Bulent Sarlioglu,et al.  Reducing Switching Losses in BLDC Motor Drives by Reducing Body Diode Conduction of MOSFETs , 2015, IEEE Transactions on Industry Applications.

[2]  Siqi Li,et al.  Analysis and Design of a New Soft-Switching Boost Converter With a Coupled Inductor , 2014, IEEE Transactions on Power Electronics.

[3]  Axel Mertens,et al.  Characterization and Scalable Modeling of Power Semiconductors for Optimized Design of Traction Inverters with Si- and SiC-Devices , 2014, IEEE Transactions on Power Electronics.

[4]  Esteban Sanchis-Kilders,et al.  A Comparative Performance Study of a 1200 V Si and SiC MOSFET Intrinsic Diode on an Induction Heating Inverter , 2014, IEEE Transactions on Power Electronics.

[5]  Takashi Hikihara,et al.  An all SiC MOSFET high performance PV converter cell , 2013, 2013 15th European Conference on Power Electronics and Applications (EPE).

[6]  R. Siemieniec,et al.  Robustness of MOSFET devices under hard commutation ofthe body diode , 2013, 2013 15th European Conference on Power Electronics and Applications (EPE).

[7]  E. Santi,et al.  Modeling, Simulation, and Validation of a Power SiC BJT , 2012, IEEE Transactions on Power Electronics.

[8]  T. Ueta,et al.  A Fast Loss and Temperature Simulation Method for Power Converters, Part I: Electrothermal Modeling and Validation , 2012, IEEE Transactions on Power Electronics.

[9]  Dawei Xiang,et al.  An Industry-Based Survey of Reliability in Power Electronic Converters , 2011, IEEE Transactions on Industry Applications.

[10]  Leon M. Tolbert,et al.  Efficiency Impact of Silicon Carbide Power Electronics for Modern Wind Turbine Full Scale Frequency Converter , 2011, IEEE Transactions on Industrial Electronics.

[11]  B. Jayant Baliga,et al.  Fundamentals of Power Semiconductor Devices , 2008 .

[12]  Salvatore Musumeci,et al.  Driving a New Monolithic Cascode Device in a DC–DC Converter Application , 2008, IEEE Transactions on Industrial Electronics.

[13]  P.R. Palmer,et al.  Physical Modeling of Fast p-i-n Diodes With Carrier Lifetime Zoning, Part I: Device Model , 2008, IEEE Transactions on Power Electronics.

[14]  E. Santi,et al.  Simulation and Optimization of Diode and Insulated Gate Bipolar Transistor Interaction in a Chopper Cell Using MATLAB and Simulink , 2007, IEEE Transactions on Industry Applications.

[15]  Takashi Hikihara,et al.  A Study on SiC Devices in Synchronous Rectification of DC-DC Converter , 2007, APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition.

[16]  A.T. Bryant,et al.  Fast Inverter Loss Simulation and Silicon Carbide Device Evaluation for Hybrid Electric Vehicle Drives , 2007, 2007 Power Conversion Conference - Nagoya.

[17]  E. Santi,et al.  Physical Modeling and Parameter Extraction Procedure for p-i-n Diodes with Lifetime Control , 2006, Conference Record of the 2006 IEEE Industry Applications Conference Forty-First IAS Annual Meeting.

[18]  A.T. Bryant,et al.  High Speed Electro-Thermal Models for Inverter Simulations , 2006, 2006 25th International Conference on Microelectronics.

[19]  Xiaosong Kang,et al.  Two-step parameter extraction procedure with formal optimization for physics-based circuit simulator IGBT and p-i-n diode models , 2006, IEEE Transactions on Power Electronics.

[20]  Petar Igic,et al.  A fast power loss calculation method for long real time thermal simulation of IGBT modules for a three-phase inverter system , 2005 .

[21]  E. Santi,et al.  A Compact Diode Model for the Simulation of Fast Power Diodes including the Effects of Avalanche and Carrier Lifetime Zoning , 2005, 2005 IEEE 36th Power Electronics Specialists Conference.

[22]  G. Ghione,et al.  Power PiN diode model for PSPICE simulations , 2005, Twentieth Annual IEEE Applied Power Electronics Conference and Exposition, 2005. APEC 2005..

[23]  W. Lour,et al.  Characterization and modeling of three-terminal heterojunction phototransistors using an InGaP layer for passivation , 2005 .

[24]  Shih-Wei Tan,et al.  Characterization and modeling of three-terminal heterojunction phototransistors using an InGaP layer for passivation , 2005, IEEE Transactions on Electron Devices.

[25]  Jerry L. Hudgins,et al.  The use of a formal optimisation procedure in automatic parameter extraction of power semiconductor devices , 2003, IEEE 34th Annual Conference on Power Electronics Specialist, 2003. PESC '03..

[26]  Xu Cheng,et al.  Improving the CoolMS/spl trade/ body-diode switching performance with integrated Schottky contacts , 2003, ISPSD '03. 2003 IEEE 15th International Symposium on Power Semiconductor Devices and ICs, 2003. Proceedings..

[27]  E. Santi,et al.  Simulation and optimisation of diode and IGBT interaction in a chopper cell using MATLAB and Simulink , 2002, Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344).

[28]  Petar Igic,et al.  Physically based compact device models for circuit modelling applications , 2001 .

[29]  T. T. Mnatsakanov,et al.  Semiempirical model of carrier mobility in silicon carbide for analyzing its dependence on temperature and doping level , 2001 .

[30]  P.A. Mawby,et al.  Dynamic electro-thermal physically based compact models of the power devices for device and circuit simulations , 2001, Seventeenth Annual IEEE Semiconductor Thermal Measurement and Management Symposium (Cat. No.01CH37189).

[31]  Francesco Iannuzzo,et al.  Measurement of the BJT activation current during the reverse recovery of power MOSFET's drain-source diode , 2001 .

[32]  Jun Zeng,et al.  Optimization of the body-diode of power MOSFETs for high efficiency synchronous rectification , 2000, 12th International Symposium on Power Semiconductor Devices & ICs. Proceedings (Cat. No.00CH37094).

[33]  G. Persiano,et al.  Experimental and numerical investigation on MOSFET's failure during reverse recovery of its internal diode , 1999 .

[34]  A. N. Githiari,et al.  A comparison of IGBT models for use in circuit design , 1997, PESC97. Record 28th Annual IEEE Power Electronics Specialists Conference. Formerly Power Conditioning Specialists Conference 1970-71. Power Processing and Electronic Specialists Conference 1972.

[35]  J. Melillo,et al.  Computer modeling of diode forward recovery characteristics , 1982, IEEE Transactions on Electron Devices.

[36]  I. Getreu,et al.  Modeling the bipolar transistor , 1978 .

[37]  R. L. Bailey,et al.  Large-signal nonlinear analysis of a high-power high-frequency junction transistor , 1970 .