Design and numerical investigation of an adaptive nozzle exit position ejector in multi-effect distillation desalination system

Few investigations have been conducted on an ejector that has an auto-tuning capability to regulate the performance of a multi-effect distillation-thermal vapour compression (MED-TVC) desalination system with the variation of operating conditions. In this study, an adaptive nozzle exit position (ANXP) ejector was first proposed to enhance ejector performance by self-adjusting the position of the primary nozzle with the change of primary pressure. A computational fluid dynamics (CFD) model was established and validated using experimental data. Simulation results indicate that there is an optimum NXP range of 43 mm–70 mm for an ejector to achieve its highest performance. The maximum increase of the entrainment ratio is 35.8% compared to that at an NXP of −30 mm. The secondary flow rate first increases and then decreases while the primary flow rate remains unchanged with the increase of the NXP in fixed working conditions. Furthermore, a correlation between optimum NXP and primary pressure was developed to provide designing parameters for the ANXP ejector.

[1]  Cai Wenjian,et al.  Area ratio effects to the performance of air-cooled ejector refrigeration cycle with R134a refrigerant , 2012 .

[2]  Navid Sharifi,et al.  An investigation of thermo-compressor design by analysis and experiment: Part 1. Validation of the numerical method , 2013 .

[3]  Sameer Khandekar,et al.  Thermo-mechanical design and characterization of flexible heat pipes , 2017 .

[4]  Haoran Chen,et al.  Experimental study on a multi-evaporator refrigeration system with variable area ratio ejector , 2016 .

[5]  Navid Sharifi,et al.  Reducing energy consumption of a steam ejector through experimental optimization of the nozzle geometry , 2014 .

[6]  Wenjian Cai,et al.  Geometry parameters effect for air-cooled ejector cooling systems with R134a refrigerant , 2012 .

[7]  Changyun Wen,et al.  Numerical investigation of geometry parameters for design of high performance ejectors , 2009 .

[8]  Wenjian Cai,et al.  Experimentation and cycle performance prediction of hybrid A/C system using automobile exhaust waste heat , 2016 .

[9]  Mikhail Sorin,et al.  Carbon capture simulation using ejectors for waste heat upgrading , 2016 .

[10]  Yanxia Li,et al.  Numerical study for the influences of primary nozzle on steam ejector performance , 2016 .

[11]  A. Jutard,et al.  Compliance adjustment of a metal bellows actuator by control law parameters , 2001 .

[12]  Wenjian Cai,et al.  Experimental study on key geometric parameters of an R134A ejector cooling system , 2016 .

[13]  Zaoxiao Zhang,et al.  An optimal multivariable controller for transcritical CO2 refrigeration cycle with an adjustable ejector , 2017 .

[14]  Navid Sharifi,et al.  An investigation of thermo-compressor design by analysis and experiment: Part 2. Development of design method by using comprehensive characteristic curves , 2013 .

[15]  David F. Bagster,et al.  A New Ejector Theory Applied to Steam Jet Refrigeration , 1977 .

[16]  W. B. Gosney.  Principles of Refrigeration , 1982 .

[17]  Wei Zhang,et al.  Experimental and numerical analysis of a variable area ratio steam ejector , 2011 .

[18]  Junjie Yan,et al.  A 1D model to predict ejector performance at critical and sub-critical operational regimesModèle unidimensionnel utilisé pour prévoir la performance d'un éjecteur sous des conditions de fonctionnement critiques et sous-critiques , 2013 .

[19]  Yasuhiro Hayakawa,et al.  Pneumatic Bellows Actuator with Force Sensing Ability and Its Application to a Pneumatic Robot , 1995, J. Robotics Mechatronics.

[20]  Mehran Ameri,et al.  Techno economic feasibility analysis of Linear Fresnel solar field as thermal source of the MED/TVC desalination system , 2016 .

[21]  Armin Hafner,et al.  Performance of fixed geometry ejectors with a swirl motion installed in a multi-ejector module of a CO2 refrigeration system , 2016 .

[22]  R. Kouhikamali,et al.  Process investigation of different locations of thermo-compressor suction in MED–TVC plants , 2011 .

[23]  Il Seouk Park.  Numerical investigation of entraining performance and operational robustness of thermal vapor compressor having swirled motive steam inflow , 2010 .

[24]  Dong-Woo Cho,et al.  Development of a micro-bellows actuator using micro-stereolithography technology , 2006 .

[25]  J. Keenan,et al.  An Investigation of Ejector Design by Analysis and Experiment , 1950 .

[26]  Armando C. Oliveira,et al.  CFD study of a variable area ratio ejector using R600a and R152a refrigerants , 2013 .

[27]  Zhongliang Liu,et al.  Experimental study on a new method for improving the performance of thermal vapor compressors for multi-effect distillation desalination systems , 2014 .

[28]  Jiyuan Tu,et al.  The spontaneously condensing phenomena in a steam-jet pump and its influence on the numerical simulation accuracy , 2012 .

[29]  Ding Zhaoqiu,et al.  Effects of superheated steam on non-equilibrium condensation in ejector primary nozzle , 2016 .

[30]  Navid Sharifi,et al.  Mixing layer effects on the entrainment ratio in steam ejectors through ideal gas computational simulations , 2016 .

[31]  Jia Yan,et al.  The characteristics of pressure recovery in an adjustable ejector multi-evaporator refrigeration system , 2012 .

[32]  Wenjian Cai,et al.  Shock circle model for ejector performance evaluation , 2007 .

[33]  Antonio Piacentino,et al.  CHP (combined heat and power) retrofit for a large MED-TVC (multiple effect distillation along with thermal vapour compression) desalination plant: High efficiency assessment for different design options under the current legislative EU framework , 2016 .

[34]  Masud Behnia,et al.  Investigation and improvement of ejector refrigeration system using computational fluid dynamics technique , 2007 .

[35]  Bing Han,et al.  Numerical investigation of the influences of mixing chamber geometries on steam ejector performance , 2014 .