Effect of cutting method on hydrogen embrittlement of high-Mn TWIP steel

[1]  M. Koyama,et al.  High-concentration carbon assists plasticity-driven hydrogen embrittlement in a Fe-high Mn steel with a relatively high stacking fault energy , 2018 .

[2]  Mingxing Zhang,et al.  The role of the microstructure on the influence of hydrogen on some advanced high-strength steels , 2018 .

[3]  Jianzhong Zhou,et al.  Influence of laser peening on the hydrogen embrittlement resistance of 316L stainless steel , 2017 .

[4]  Mingxing Zhang,et al.  Hydrogen influence on some advanced high-strength steels , 2017 .

[5]  Oreste S. Bursi,et al.  Laser and mechanical cutting effects on the cut-edge properties of steel S355N , 2017 .

[6]  P. Rivera-Díaz-del-Castillo,et al.  Understanding martensite and twin formation in austenitic steels: A model describing TRIP and TWIP effects , 2017 .

[7]  Taekyung Lee,et al.  Effect of Al addition on low-cycle fatigue properties of hydrogen-charged high-Mn TWIP steels , 2016 .

[8]  H. Maier,et al.  Effect of strain rate on hydrogen embrittlement susceptibility of twinning-induced plasticity steel pre-charged with high-pressure hydrogen gas , 2016 .

[9]  M. Koyama,et al.  Hydrogen Embrittlement Susceptibility of Fe-Mn Binary Alloys with High Mn Content: Effects of Stable and Metastable ε-Martensite, and Mn Concentration , 2016, Metallurgical and Materials Transactions A.

[10]  N. Tsuji,et al.  Effect of grain refinement on hydrogen embrittlement behaviors of high-Mn TWIP steel , 2016 .

[11]  W. Bleck,et al.  Effects of grain size on hydrogen embrittlement in a Fe-22Mn-0.6C TWIP steel , 2015 .

[12]  Young-Soo Chun,et al.  Role of Cu on hydrogen embrittlement behavior in Fe–Mn–C–Cu TWIP steel , 2015 .

[13]  Hyunkyu Jeon,et al.  The advantage of grain refinement in the hydrogen embrittlement of Fe–18Mn–0.6C twinning-induced plasticity steel , 2015 .

[14]  Young‐kook Lee,et al.  The effect of Ti precipitates on hydrogen embrittlement of Fe–18Mn–0.6C–2Al–xTi twinning-induced plasticity steel , 2014 .

[15]  X. M. Chen,et al.  Edge cracking mechanism in two dual-phase advanced high strength steels , 2014 .

[16]  Todd M. Mower,et al.  Degradation of titanium 6Al–4V fatigue strength due to electrical discharge machining , 2014 .

[17]  J. Lesage,et al.  X-ray diffraction study of microstructural changes during fatigue damage initiation in pipe steels: Role of the initial dislocation structure , 2013 .

[18]  M. Koyama,et al.  Hydrogen-assisted failure in a twinning-induced plasticity steel studied under in situ hydrogen char , 2013 .

[19]  Chun‐Sing Lee,et al.  Delayed static failure of twinning-induced plasticity steels , 2012 .

[20]  Young‐kook Lee,et al.  The mechanism of enhanced resistance to the hydrogen delayed fracture in Al-added Fe–18Mn–0.6C twinning-induced plasticity steels , 2012 .

[21]  M. Koyama,et al.  Effect of hydrogen content on the embrittlement in a Fe–Mn–C twinning-induced plasticity steel , 2012 .

[22]  A. Deschamps,et al.  Hydrogen trapping by VC precipitates and structural defects in a high strength Fe–Mn–C steel studied by small-angle neutron scattering , 2012 .

[23]  O. Takakuwa,et al.  Numerical simulation of the effects of residual stress on the concentration of hydrogen around a crack tip , 2012 .

[24]  Young-Soo Chun,et al.  Role of ɛ martensite in tensile properties and hydrogen degradation of high-Mn steels , 2012 .

[25]  Helmut Schaeben,et al.  Grain detection from 2d and 3d EBSD data--specification of the MTEX algorithm. , 2011, Ultramicroscopy.

[26]  O. Bouaziz,et al.  High manganese austenitic twinning induced plasticity steels: A review of the microstructure properties relationships , 2011 .

[27]  Sunghak Lee,et al.  Effects of Al addition on deformation and fracture mechanisms in two high manganese TWIP steels , 2011 .

[28]  Mark Whittaker,et al.  The influence of mechanical and CO2 laser cut-edge characteristics on the fatigue life performance of high strength automotive steels , 2011 .

[29]  Janet Folkes,et al.  Waterjet—An innovative tool for manufacturing , 2009 .

[30]  Daniel J. Thomas.  Characteristics of abrasive waterjet cut-edges and the affect on formability and fatigue performance of high strength steels , 2009 .

[31]  Jacques Besson,et al.  Effect of shear cutting on ductility of a dual phase steel , 2009 .

[32]  S. Yao,et al.  Microstructure analysis of the martensitic stainless steel surface fine-cut by the wire electrode discharge machining (WEDM) , 2004 .

[33]  Y. Estrin,et al.  Twinning-induced plasticity (TWIP) steels , 2018 .

[34]  M. Koyama,et al.  Spatially and Kinetically Resolved Mapping of Hydrogen in a Twinning-Induced Plasticity Steel by Use of Scanning Kelvin Probe Force Microscopy , 2015 .

[35]  Dierk Raabe,et al.  Revealing the strain-hardening behavior of twinning-induced plasticity steels: Theory, simulations, , 2013 .

[36]  M. Koyama,et al.  Hydrogen embrittlement in a Fe–Mn–C ternary twinning-induced plasticity steel , 2012 .

[37]  Kwansoo Chung,et al.  Formability of TWIP (twinning induced plasticity) automotive sheets , 2011 .