Development of an Electromagnetic Energy Harvester for Monitoring Wind Turbine Blades

Wind turbine blades experience tremendous stresses while in operation. Failure of a blade can damage other components or other wind turbines. This research focuses on developing an electromagnetic energy harvester for powering structural health monitoring (SHM) equipment inside a turbine blade. The harvester consists of a magnet inside a tube with coils outside the tube. The changing orientation of the blade causes the magnet to slide along the tube, inducing a voltage in the coils which in turn powers the SHM system. This thesis begins with a brief history of electromagnetic energy harvesting and energy harvesters in rotating environments. Next a model of the harvester is developed encompassing the motion of the magnet, the current in the electrical circuit, and the coupling between the mechanical and electrical domains. The nonlinear coupling factor is derived from Faraday’s law of induction and from modeling the magnet as a magnetic dipole moment. Three experiments are performed to validate the model: a free fall test to verify the coupling factor expression, a rotating test to study the model with a load resistor circuit, and a capacitor charging test to examine the model with an energy storage circuit. The validated model is then examined under varying tube lengths and positions, varying coil sizes and positions, and variations in other parameters. Finally a sample harvester is presented that can power an SHM system inside a large scale wind turbine blade spinning up to 20 RPM and can produce up to 14.1 mW at 19 RPM.

[1]  H. Polinder,et al.  Linear PM Generator system for wave energy conversion in the AWS , 2004, IEEE Transactions on Energy Conversion.

[2]  T K A Brekken,et al.  A Permanent-Magnet Tubular Linear Generator for Ocean Wave Energy Conversion , 2010, IEEE Transactions on Industry Applications.

[3]  Eric M. Yeatman,et al.  Energy harvesting from motion using rotating and gyroscopic proof masses , 2008 .

[4]  Adam J. Sneller,et al.  On the nonlinear electromagnetic coupling between a coil and an oscillating magnet , 2010 .

[5]  Chengkuo Lee,et al.  Hybrid energy harvester based on piezoelectric and electromagnetic mechanisms , 2010 .

[6]  Chengkuo Lee,et al.  Electromagnetic energy harvesting from vibrations of multiple frequencies , 2009 .

[7]  E.O. Torres,et al.  Electrostatic Energy Harvester and Li-Ion Charger Circuit for Micro-Scale Applications , 2006, 2006 49th IEEE International Midwest Symposium on Circuits and Systems.

[8]  Jeffrey H. Lang,et al.  A Device for Harvesting Energy From Rotational Vibrations , 2010 .

[9]  F. Wurtz,et al.  Interaction between ring-shaped permanent magnets with symbolic gradients: application to magnetic bearing system optimization , 2010, Digests of the 2010 14th Biennial IEEE Conference on Electromagnetic Field Computation.

[10]  J. Jonkman,et al.  Definition of a 5-MW Reference Wind Turbine for Offshore System Development , 2009 .

[11]  S. Beeby,et al.  Energy harvesting vibration sources for microsystems applications , 2006 .

[12]  Rajeevan Amirtharajah,et al.  Self-powered signal processing using vibration-based power generation , 1998, IEEE J. Solid State Circuits.

[13]  Eric M. Yeatman,et al.  CONTINUOUSLY ROTATING ENERGY HARVESTER WITH IMPROVED POWER DENSITY , 2008 .

[14]  T.C. Green,et al.  Architectures for vibration-driven micropower generators , 2004, Journal of Microelectromechanical Systems.

[15]  Yiannos Manoli,et al.  Numerical optimization approach for resonant electromagnetic vibration transducer designed for random vibration , 2008 .

[16]  Shashank Priya,et al.  Pen harvester for powering a pulse rate sensor , 2009 .

[17]  Daniel J. Inman,et al.  Impedance-based structural health monitoring of wind turbine blades , 2007, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[18]  Lei Wang,et al.  Energy harvesting by magnetostrictive material (MsM) for powering wireless sensors in SHM , 2007, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[19]  M. Hand,et al.  Wind Turbine Design Cost and Scaling Model , 2006 .

[20]  Yu Zhou,et al.  Design and characterization of an electromagnetic energy harvester for vehicle suspensions , 2010 .

[21]  N. M. White,et al.  Harvesting energy from vehicle wheels , 2009, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[22]  Jung-Ryul Lee,et al.  Structural health monitoring for a wind turbine system: a review of damage detection methods , 2008 .

[23]  John E. Hurtado,et al.  Structural health monitoring of wind turbines , 1997 .

[24]  Frank T. Fisher,et al.  A coupled piezoelectric–electromagnetic energy harvesting technique for achieving increased power output through damping matching , 2009 .

[25]  D.P. Arnold,et al.  Review of Microscale Magnetic Power Generation , 2007, IEEE Transactions on Magnetics.

[26]  Eric M. Yeatman,et al.  Energy Harvesting From Rotating Structures , 2007 .

[27]  Daniel J. Inman,et al.  Energy Harvesting Technologies , 2008 .

[28]  Stephen D. Conrad Development of an inertial generator for embedded applications in rotating environments , 2007 .

[29]  S. Salon,et al.  Coupling Factor Between the Magnetic and Mechanical Energy Domains in Electromagnetic Power Harvesting Applications , 2011, IEEE Transactions on Magnetics.

[30]  Ronald D. Snee,et al.  Industry, Statistics in , 2006 .

[31]  Long Lin,et al.  A Nanogenerator for Energy Harvesting from a Rotating Tire and its Application as a Self‐Powered Pressure/Speed Sensor , 2011, Advanced materials.

[32]  Dibin Zhu,et al.  Design and experimental characterization of a tunable vibration-based electromagnetic micro-generator , 2010 .

[33]  R. B. Yates,et al.  Analysis Of A Micro-electric Generator For Microsystems , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[34]  Charles R. Farrar,et al.  Energy Harvesting for Structural Health Monitoring Sensor Networks , 2008 .

[35]  Neil M. White,et al.  Design and fabrication of a new vibration-based electromechanical power generator , 2001 .

[36]  Kevin M. Farinholt,et al.  Energy harvesting to power sensing hardware onboard wind turbine blade , 2011 .

[37]  Ramesh Govindan,et al.  Embedded sensing of structures: a reality check , 2005, 11th IEEE International Conference on Embedded and Real-Time Computing Systems and Applications (RTCSA'05).

[38]  Susumu Sugiyama,et al.  A micro electromagnetic low level vibration energy harvester based on MEMS technology , 2009 .

[39]  Steven L. Garrett,et al.  Characterization of a small moving-magnet electrodynamic linear motor , 2005 .

[40]  Celso L. Ladera,et al.  Magnet fall inside a conductive pipe: motion and the role of the pipe wall thickness , 2009 .

[41]  H. A. Wheeler Simple Inductance Formulas for Radio Coils , 1928, Proceedings of the Institute of Radio Engineers.

[42]  R. B. Yates,et al.  Development of an electromagnetic micro-generator , 2001 .

[43]  J. Farmer,et al.  A comparison of power harvesting techniques and related energy storage issues , 2007 .

[44]  Paul D. Mitcheson Analysis and optimisation of energy-harvesting micro-generator systems , 2005 .

[45]  Eric M. Yeatman,et al.  A continuously rotating energy harvester with maximum power point tracking , 2008 .

[46]  Mehrdad Moallem,et al.  Modeling and Analysis of a Piezoelectric Energy Scavenger for Rotary Motion Applications , 2011 .

[47]  Cheng-Kuo Sung,et al.  Design of a frequency-adjusting device for harvesting energy from a rotating wheel , 2010 .