Performance Assessment of Warm Mix Asphalt (WMA) Pavements

Warm Mix Asphalt (WMA) is a new technology that was introduced in Europe in 1995. WMA offers several advantages over conventional asphalt concrete mixtures, including: reduced energy consumption, reduced emissions, improved or more uniform binder coating of aggregate which should reduce mix surface aging, and extended construction season in temperate climates. Three WMA techniques, Aspha-min, Sasobit, and Evotherm, were used to reduce the viscosity of the asphalt binder at certain temperatures and to dry and fully coat the aggregates at a lower production temperature than conventional hot mix asphalt. The reduction in mixing and compaction temperatures of asphalt mixtures leads to a reduction in both fuel consumption and emissions. This research project had two major components, the outdoor field study on SR541 in Guernsey County and the indoor study in the Accelerated Pavement Load Facility (APLF). Each study included the application of four types of asphalt surface layer, including standard hot mix asphalt as a control and three warm mixes: Evotherm, Aspha-min, and Sasobit. The outdoor study began with testing of the preexisting pavement and subgrade, the results of which indicated that while the pavement and subgrade were not uniform, there were no significant problems or variations that would be expected to lead to differences in performance of the planned test sections. During construction, the outdoor study included collection of emissions samples at the plant and on the construction site as well as thermal readings from the site. Afterwards, the outdoor study included the periodic collection and laboratory analysis of core samples and visual inspections of the road. Roughness (IRI) measurements were made shortly after construction and after a year of service. The indoor study involved the construction of four lanes of perpetual pavement, each topped with one of the test mixes. The lanes were further divided into northern and southern halves, with the northern halves having a full 16 in (40 cm) perpetual pavement, and with the southern halves with thicknesses decreasing in 1 in. (2.5 cm) increments by reducing the intermediate layer. The dense graded aggregate base was increased to compensate for the change in pavement thickness. The southern half of each lane was instrumented to measure temperature, subgrade pressure, deflection relative to top of subgrade and to a point 5 ft (1.5 m) down, and longitudinal and transverse strains at the base of the fatigue resistance layer (FRL). The APLF had the temperature set to 40°F (4.4°C), 70°F (21.1°C), and 104°F (40°C), in that order. At each temperature, rolling wheel loads of 6000 lb (26.7 kN), 9000 lb (40 kN), and 12,000 lb (53.4 kN) were applied at lateral shifts of 3 in. (76 mm), 1 in. (25 mm), -4 in. (-102 mm), and -9 in. (- 229 mm) and the response measured. Then each plane was subjected to 10,000 passes of the rolling wheel load of 9000 lb (40 kN) at about 5 mph (8 km/h). Profiles were measured after 100, 300, 1000, 3000, and 10,000 passes with a profilometer to assess consolidation of each surface. After the 10,000 passes of the rolling wheel load were completed, a second set of measurements was made under rolling wheel loads of 6000 lb (26.7 kN), 9000 lb (40 kN), and 12,000 lb (53.4 kN) at the same lateral shifts as before. Additionally, the response of the pavement instrumentation was recorded during drops of a Falling Weight Deflectometer (FWD).

[1]  Shad Sargand,et al.  Use of Dynamic Cone Penetrometer in Subgrade and Base Acceptance , 2007 .

[2]  Brian D. Prowell,et al.  NCAT Report 09-04 OHIO FIELD TRIAL OF WARM MIX ASPHALT TECHNOLOGIES : CONSTRUCTION SUMMARY By , 2010 .

[3]  J D'angelo,et al.  MATERIAL PRODUCTION, MIX DESIGN, AND PAVEMENT DESIGN EFFECTS ON MOISTURE DAMAGE , 2003 .

[4]  M von Devivere,et al.  WARM ASPHALT MIXES BY ADDING A SYNTHETIC ZEOLITE , 2003 .

[5]  Brian D Prowell,et al.  Evaluation of Aspha-Min® Zeolite for Use in Warm Mix Asphalt , 2005 .

[6]  F L Roberts,et al.  Stripping in HMA Mixtures: State-of-the-Art and Critical Review of Test Methods , 1988 .

[7]  J. S. Lai,et al.  Creep and Relaxation of Nonlinear Viscoelastic Materials , 2011 .

[8]  Shad Sargand Integrating Warm Asphalt and Perpetual Pavement , 2007 .

[9]  S Maccarrone,et al.  Cold asphalt systems as an alternative to hotmix , 1995 .

[10]  M. Chaudhury,et al.  Interfacial Lifshitz-van der Waals and polar interactions in macroscopic systems , 1988 .

[11]  KJ Jenkins,et al.  HALF-WARM FOAMED BITUMEN TREATMENT , A NEW PROCESS , .

[12]  John D'Angelo,et al.  X-ray Tomography to Characterize Air Void Distribution in Superpave Gyratory Compacted Specimens , 2002 .

[13]  Edith Arambula Mercado,et al.  Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes , 2009 .

[14]  T Harrison,et al.  Innovative processes in asphalt production and application: "Strengthening asphalt's position in helping to build a better world" , 2000 .

[15]  Shad M. Sargand,et al.  Instrumentation of the WAY-30 Test Pavements , 2008 .

[16]  John T Harvey,et al.  TEST METHODS TO PREDICT MOISTURE SENSITIVITY OF HOT-MIX ASPHALT PAVEMENTS , 2003 .

[17]  E Ray Brown,et al.  Workability of Hot-Mix Asphalt , 2004 .

[18]  Andrew Wimsatt,et al.  A Synthesis of Warm-Mix Asphalt , 2007 .

[19]  Imad L. Al-Qadi,et al.  Direct Observation of Bitumen-Aggregate Interface , 2009 .

[20]  Ashley Buss,et al.  Investigation of Warm-Mix Asphalt Using Iowa Aggregates , 2011 .

[21]  Junboum Park,et al.  Adsorption and Thermal Desorption Behaviour of Asphalt-like Functionalities on Silica , 2000 .

[22]  Hans-Ruedi Hug,et al.  Color Plate 2 , 2008 .

[23]  U. Isacsson,et al.  Influence of commercial waxes and polyphosphoric acid on bitumen and asphalt concrete performance at low and medium temperatures , 2007 .

[24]  Thomas Harman,et al.  PROPOSED METHODOLOGY FOR PREDICTING HMA PERMEABILITY (WITH DISCUSSION) , 2002 .

[25]  O. Kristjansdottir,et al.  Warm Mix Asphalt for Cold Weather Paving , 2006 .

[26]  Maupin INVESTIGATION OF TEST METHODS, PAVEMENTS, AND LABORATORY DESIGN RELATED TO ASPHALT PERMEABILITY , 2000 .

[27]  Elizabeth K. Easby Color Plate 9 , 2008 .

[28]  Tejash Gandhi,et al.  EFFECTS OF WARM ASPHALT ADDITIVES ON ASPHALT BINDER AND MIXTURE PROPERTIES , 2008 .

[29]  Rafiqul A. Tarefder,et al.  Nanoscale Evaluation of Moisture Damage in Polymer Modified Asphalts , 2010 .

[30]  Björn Birgisson,et al.  Analytical derivation of permeability and numerical simulation of fluid flow in hot-mix asphalt , 2004 .

[31]  R G Hicks,et al.  INTRODUCTION AND SEMINAR OBJECTIVES , 2003 .

[32]  Kuei Yi Lin,et al.  Effects of Crack Width and Permeability on Moisture-Induced Damage of Pavements , 2004 .

[33]  Dallas N. Little,et al.  Using Surface Energy Measurements to Select Materials for Asphalt Pavement , 2006 .

[34]  D. Newcomb,et al.  Viscoelastic Behavior of Asphalt Concrete in Diametral Compression , 1997 .

[35]  Musharraf Zaman,et al.  Effect of Sasobit and Aspha-Min on Wettability and Adhesion between Asphalt Binders and Aggregates , 2008 .

[36]  Steve L. Webster,et al.  DESCRIPTION AND APPLICATION OF DUAL MASS DYNAMIC CONE PENETROMETER. FINAL REPORT , 1992 .

[37]  Ulf Isacsson,et al.  Rheological effects of commercial waxes and polyphosphoric acid in bitumen 160/220 : low temperature performance , 2006 .

[38]  Mohamed M El-Basyouny,et al.  SIMPLE PERFORMANCE TEST FOR SUPERPAVE MIX DESIGN , 2002 .

[39]  R. Hicks Moisture damage in asphalt concrete , 1991 .

[40]  Shad M. Sargand,et al.  Determination of Pavement Layer Stiffness on the Ohio SHRP Test Road Using Non-Destructive Testing Techniques , 2002 .

[41]  Robert L. Lytton,et al.  Measurements of Surface Energy and Its Relationship to Moisture Damage , 2005 .

[42]  B G Koenders,et al.  WAM-FOAM, ASPHALT PRODUCTION AT LOWER OPERATING TEMPERATURES , 2002 .

[43]  Brian D Prowell,et al.  MICHIGAN FIELD TRIAL OF WARM MIX ASPHALT TECHNOLOGIES: CONSTRUCTION SUMMARY , 2009 .

[44]  J Emery,et al.  MOISTURE DAMAGE OF ASPHALT PAVEMENTS AND ANTISTRIPPING ADDITIVES: CAUSES, IDENTIFICATION, TESTING AND MITIGATION , 1997 .

[45]  William D. Harkins,et al.  THE ORIENTATION OF MOLECULES IN SURFACES. VI. COHESION, ADHESION, TENSILE STRENGTH, TENSILE ENERGY, NEGATIVE SURFACE ENERGY, INTERFACIAL TENSION, AND MOLECULAR ATTRACTION. , 1920 .

[46]  B G Koenders,et al.  INNOVATIVE PROCESS IN ASPHALT PRODUCTION AND APPLICATION TO OBTAIN LOWER OPERATING TEMPERATURES , 2000 .

[47]  L A Cooley,et al.  PRODUCTION AND CONSTRUCTION ISSUES FOR MOISTURE SENSITIVITY OF HOT-MIX ASPHALT PAVEMENTS , 2003 .

[48]  Yuzhen Zhang,et al.  Influence of Commercial Wax on Performance of Asphalt , 2010 .

[49]  J. C. Petersen,et al.  MODEL STUDIES AND INTERPRETIVE REVIEW OF THE COMPETITIVE ADSORPTION AND WATER DISPLACEMENT OF PETROLEUM ASPHALT CHEMICAL FUNCTIONALITIES ON MINERAL AGGREGATE SURFACES , 1998 .

[50]  Brian D Prowell,et al.  Evaluation of Sasobit® for Use in Warm Mix Asphalt , 2005 .

[51]  Louay N. Mohammad,et al.  Evaluation of Permeability of Superpav® Asphalt Mixtures , 2003 .

[52]  Robert L. Lytton,et al.  Simple Method for Predicting Laboratory and Field Permeability of Hot-Mix Asphalt , 2006 .

[53]  Eyad Masad,et al.  Three dimensional simulation of fluid flow in X‐ray CT images of porous media , 2004 .

[54]  Brian D Prowell,et al.  Evaluation of Evotherm® for use in Warm Mix Asphalt , 2006 .

[55]  Randy B Machemehl,et al.  STRIPPING AND MOISTURE DAMAGE IN ASPHALT MIXTURES , 1984 .

[56]  Larry Michael,et al.  Assessing Potential for Warm-Mix Asphalt Technology Adoption , 2007 .

[57]  Shad M. Sargand,et al.  Forensic Investigation of AC and PCC Pavements With Extended Service Life: Volume 1 , 2010 .

[58]  Shad M. Sargand,et al.  Performance assessment of warm mix asphalt (WMA) pavements : executive summary report. , 2009 .