A dual nozzle 3D printing system for super soft composite hydrogels

Abstract Due to their inability to sustain their own weight, 3D printing materials as soft as human tissues is challenging. Hereby we describe the development of an extrusion additive manufacturing (AM) machine able to 3D print super soft hydrogels with micro-scale precision. By designing and integrating new subsystems into a conventional extrusion-based 3D printer, we obtained hardware that encompasses a range of new capabilities. In particular, we integrated a heated dual nozzle extrusion system and a cooling platform in the new system. In addition, we altered the electronics and software of the 3D printer to ensure fully automatized procedures are delivered by the 3D printing device, and super-soft tissue mimicking parts are produced. With regards to the electronics, we added new devices to control the temperature of the extrusion system. As for the software, the firmware of the conventional 3D printer was changed and modified to allow for the flow rate control of the ink, thus eliminating overflows in sections of the printing path where the direction/speed changes sharply.

[1]  F. Rodriguez y Baena,et al.  Composite hydrogel: A high fidelity soft tissue mimic for surgery , 2018, Materials & Design.

[2]  Ming-Chuan Leu,et al.  Study of Part Geometric Features and Support Materials in Rapid Freeze Prototyping , 2003 .

[3]  J. G. Williams,et al.  Modelling and experimental characterisation of the rate dependent fracture properties of gelatine gels , 2015 .

[4]  Joon Hyung Park,et al.  Three-dimensional printing of complex biological structures by freeform reversible embedding of suspended hydrogels , 2015, Science Advances.

[5]  P. Ström,et al.  Validation and learning in the Procedicus KSA virtual reality surgical simulator , 2003, Surgical Endoscopy And Other Interventional Techniques.

[6]  Ibrahim T. Ozbolat,et al.  Current advances and future perspectives in extrusion-based bioprinting. , 2016, Biomaterials.

[7]  Joachim P Spatz,et al.  Stem cell migration and mechanotransduction on linear stiffness gradient hydrogels , 2017, Proceedings of the National Academy of Sciences.

[8]  J. Michelson,et al.  Simulation in orthopaedic education: an overview of theory and practice. , 2006, The Journal of bone and joint surgery. American volume.

[9]  D. Dini,et al.  A composite hydrogel for brain tissue phantoms , 2016 .

[10]  Daniele Dini,et al.  Cryogenic 3D Printing of Super Soft Hydrogels , 2017, Scientific Reports.

[11]  Enas M. Ahmed,et al.  Hydrogel: Preparation, characterization, and applications: A review , 2013, Journal of advanced research.

[12]  Z. Ji,et al.  Rapid Freezing Prototyping with Water , 1999 .

[13]  Anthony Atala,et al.  De novo reconstitution of a functional mammalian urinary bladder by tissue engineering , 1999, Nature Biotechnology.

[14]  Ferdinando Rodriguez y Baena,et al.  Soft Tissue Phantoms for Realistic Needle Insertion: A Comparative Study , 2015, Annals of Biomedical Engineering.

[15]  N. Vrana,et al.  Polyvinvyl Alcohol-Based Cryogels: Tissue Engineering and Regenerative Medicine , 2015 .

[16]  Stuart K Williams,et al.  Direct-write bioprinting three-dimensional biohybrid systems for future regenerative therapies. , 2011, Journal of biomedical materials research. Part B, Applied biomaterials.

[17]  Michele Marcolongo,et al.  Characterization of cell viability during bioprinting processes. , 2009, Biotechnology journal.

[18]  Peter Dubruel,et al.  A review of trends and limitations in hydrogel-rapid prototyping for tissue engineering. , 2012, Biomaterials.

[19]  Barry J. Doyle,et al.  Parameter optimization for 3D bioprinting of hydrogels , 2017 .

[20]  Marc E. Nelson,et al.  Bioresorbable airway splint created with a three-dimensional printer. , 2013, The New England journal of medicine.

[21]  Kah Fai Leong,et al.  Rapid freeze prototyping technique in bio‐plotters for tissue scaffold fabrication , 2008 .

[22]  Lay Poh Tan,et al.  Current Status of Bioinks for Micro-Extrusion-Based 3D Bioprinting , 2016, Molecules.

[23]  Ibrahim T. Ozbolat,et al.  Bioprinting Toward Organ Fabrication: Challenges and Future Trends , 2013, IEEE Transactions on Biomedical Engineering.

[24]  Helium Mak,et al.  Poly(Vinyl Alcohol) Cryogels for Biomedical Applications , 2014 .

[25]  Stefano Galvan,et al.  Models and tissue mimics for brain shift simulations , 2017, Biomechanics and Modeling in Mechanobiology.

[26]  Wei Zhang,et al.  An Experimental and Analytical Study of Ice Part Fabrication with Rapid Freeze Prototyping , 2000 .

[27]  Aatman Shah,et al.  Materials used in cranioplasty: a history and analysis. , 2014, Neurosurgical focus.

[28]  Kira Pusch,et al.  Large volume syringe pump extruder for desktop 3D printers , 2018, HardwareX.

[29]  Robert J. Strong,et al.  A review of melt extrusion additive manufacturing processes: I. Process design and modeling , 2014 .

[30]  B. Rubinsky,et al.  Cryogenic 3D printing for tissue engineering. , 2015, Cryobiology.

[31]  S. Fare',et al.  3D printing of methylcellulose-based hydrogels , 2018, Bioprinting.

[32]  J. Tardif,et al.  Polyvinyl alcohol cryogel: optimizing the parameters of cryogenic treatment using hyperelastic models. , 2009, Journal of the mechanical behavior of biomedical materials.

[33]  George-Christopher Vosniakos,et al.  On the development of a robot-operated 3D-printer , 2018 .