Establishing a sidewall image transfer chemo-epitaxial DSA process using 193 nm immersion lithography

Directed Self-Assembly (DSA) of Block Copolymers (BCP) by chemo-epitaxial alignment is a promising high resolution lithography technique compatible with CMOS high-volume manufacturing. It allows overcoming limitations in resolution and local stochasticity by conventional, imaging based, lithography. However, for BCP with pitches below 20 nm and guide patterning by immersion lithography (193i), multiplication factors ≥ 4 become necessary, imposing stringent requirements on the guides and defectivity becomes hard to control. The Arkema-CEA (ACE) process flow overcomes this limit by creating the guides by a self-aligned double patterning (SADP) process flow, followed by the deposition of a cross-linkable neutral mat and selective grafting of the guides. This paper reports on the transfer of the process flow to immersion lithography, details challenges encountered in process optimization, notably the dependence of the wetting of the neutral layer on the surface energy and the morphology of the spacers. Last, the paper presents a metrology and defectivity roadmap combined with preliminary, promising results.

[1]  L. Leibler.  Theory of Microphase Separation in Block Copolymers , 1980 .

[2]  William H. Woodall,et al.  Introduction to Statistical Quality Control, Fifth Edition , 2005 .

[3]  Jun Ishikawa,et al.  Double patterning requirements for optical lithography and prospects for optical extension without double patterning , 2008, SPIE Advanced Lithography.

[4]  Fred Spiring,et al.  Introduction to Statistical Quality Control , 2007, Technometrics.

[5]  Gijsbert Rispens,et al.  High-numerical aperture extreme ultraviolet scanner for 8-nm lithography and beyond , 2017 .

[6]  Masafumi Asano,et al.  Effect of measurement error budgets and hybrid metrology on qualification metrology sampling , 2014 .

[7]  Jianhui Shan,et al.  Toward high-performance quality meeting IC device manufacturing requirements with AZ SMART DSA process , 2015, Advanced Lithography.

[8]  G.E. Moore,et al.  Cramming More Components Onto Integrated Circuits , 1998, Proceedings of the IEEE.

[9]  Hyo Seon Suh,et al.  Kinetic approach to defect reduction in directed self-assembly , 2019, Journal of Micro/Nanolithography, MEMS, and MOEMS.

[10]  Clair Webb,et al.  Intel design for manufacturing and evolution of design rules , 2008, SPIE Advanced Lithography.

[11]  Moshe Dolejsi,et al.  Combining double patterning with self-assembled block copolymer lamellae to fabricate 10.5 nm full-pitch line/space patterns , 2019, Nanotechnology.

[12]  Eungnak Han,et al.  Fabrication of Lithographically Defined Chemically Patterned Polymer Brushes and Mats , 2011 .

[13]  L. Pain,et al.  Spacer patterning lithography as a new process to induce block copolymer alignment by chemo-epitaxy , 2019, Advanced Lithography.

[14]  Sungki Park,et al.  Patterning with spacer for expanding the resolution limit of current lithography tool , 2006, SPIE Advanced Lithography.

[15]  Mark Neisser,et al.  The 2017 IRDS Lithography Roadmap , 2018 .

[16]  Patrick Jaenen,et al.  Pitch doubling through dual-patterning lithography challenges in integration and litho budgets , 2007, SPIE Advanced Lithography.

[17]  Masahiko Harumoto,et al.  Expanding DSA process window with atmospheric control , 2020, Advanced Lithography.

[18]  Geert Vandenberghe,et al.  Strategies for Increasing the Rate of Defect Annihilation in the Directed Self-Assembly of High-Chi Block Copolymers. , 2019, ACS applied materials & interfaces.

[19]  Geert Vandenberghe,et al.  Comparing positive and negative tone development process for printing the metal and contact layers of the 32- and 22-nm nodes , 2010 .

[20]  Olivier Joubert,et al.  Unbiased line width roughness measurements with critical dimension scanning electron microscopy and critical dimension atomic force microscopy , 2012 .

[21]  Charles N. Archie,et al.  Scatterometry measurement precision and accuracy below 70 nm , 2003, SPIE Advanced Lithography.

[22]  Robert Chau,et al.  Process and Packaging Innovations for Moore’s Law Continuation and Beyond , 2019, 2019 IEEE International Electron Devices Meeting (IEDM).

[23]  Thomas Schmoeller,et al.  Rigorous assessment of patterning solution of metal layer in 7 nm technology node , 2016 .