Effects of component performance on overall performance of R410A air conditioner with oil flooding and regeneration

Abstract Oil flooded compression with regenerator (OFCR) is one of the possible technologies to improve the performance of air conditioner. The addition of OFCR system to basic vapor compression system adds several components: oil separator, oil cooler and regenerator. These components can lead to a significant increase in performance. In this study, parametric studies of these components performance have been carried out under various operating conditions. Compared with basic vapor compression system, COP of OFCR system with 100% effective regenerator is improved by 0.7–11.8% while COP of OFCR system without regenerator is reduced by 0.6–1.8%. When oil temperature exiting the oil cooler reaches 40 °C and 50 °C, the performance of OFCR system is worse than that of basic system at evaporation temperature Te = 15 °C and Te ⩾ 5 °C respectively. COP and cooling capacity of OFCR with solubility are decreased by 6.9% and 14.3% respectively at Te = 5 °C and 0.4 oil mass fraction. A modification of OFCR system is suggested for reducing the negative effects of solubility. The results of COP and cooling capacity show that the modified OFCR system has a 3–4% performance improvement. Comprehensive effects of regenerator efficiency, oil temperature and solubility are also studied. Taking the solubility into account, the effects of regenerator efficiency and oil temperature are slightly different from that without solubility.

[1]  Lin Lu,et al.  Energy performance of solar-assisted liquid desiccant air-conditioning system for commercial building in main climate zones , 2014 .

[2]  James E. Braun,et al.  Performance limit for economized cycles with continuous refrigerant injection. , 2011 .

[3]  Reinhard Radermacher,et al.  Investigation of potential benefits of compressor cooling , 2008 .

[4]  K. F. Fong,et al.  Comparative study of solar cooling systems with building-integrated solar collectors for use in sub-tropical regions like Hong Kong , 2012 .

[5]  Antonio Giuffrida,et al.  A semi-empirical method for assessing the performance of an open-drive screw refrigeration compressor , 2016 .

[6]  Jason J Hugenroth,et al.  Liquid flooded Ericsson cycle cooler , 2006 .

[7]  Huiming Zou,et al.  Experimental investigation on heating performance of heat pump for electric vehicles at −20 °C ambient temperature , 2015 .

[8]  W. T. Horton,et al.  Experimental testing of an oil-flooded hermetic scroll compressor , 2013 .

[9]  Jahar Sarkar,et al.  Ejector enhanced vapor compression refrigeration and heat pump systems—A review , 2012 .

[10]  Reinhard Radermacher,et al.  Potential benefits of saturation cycle with two-phase refrigerant injection , 2013 .

[11]  Sugirdhalakshmi Ramaraj.  Vapor compression cycle enhancements for cold climate heat pumps , 2012 .

[12]  Mike W. Coney,et al.  Development Of A Reciprocating Compressor Using Water Injection To Achieve Quasi-Isothermal Compression , 2002 .

[13]  Bijan Samali,et al.  A review of different strategies for HVAC energy saving , 2014 .

[14]  W. T. Horton,et al.  Experimental analysis of oil flooded R410A scroll compressor , 2014 .

[15]  Jean Lebrun,et al.  Scroll compressors using gas and liquid injection: experimental analysis and modelling , 2002 .

[16]  Siaw Kiang Chou,et al.  Achieving better energy-efficient air conditioning - A review of technologies and strategies , 2013 .

[17]  James E. Braun,et al.  Performance of Vapor Compression Systems with Compressor Oil Flooding and Regeneration , 2011 .

[18]  Shinji Doki,et al.  Realization of highly efficient and small IPM motors for the compressors of air-conditioners , 2015, 2015 IEEE International Conference on Industrial Technology (ICIT).

[19]  W. T. Horton,et al.  Impact of Oil Solubility and Refrigerant Flashing on the Performance of Transcritical CO2 Vapor Compression Systems with Oil Flooding and Regeneration , 2010 .