FAILURE MAPPING PROCESS: AN APPLIED STUDY IN A SHIPYARD FACILITY

Faults represent non-conformities in productive activities. Therefore, approaches to their mitigation are relevant. Risk management techniques enable effective company’s strategic planning and the adoption of process controls towards failure reduction and assurance of adequate occupational health and safety. This research purported to integrate four widespread techniques, which are usually applied as stand-alone tools, to provide a robust risk management approach. A literature review about Process Mapping, Preliminary Hazard Analysis (PHA), Fault Tree Analysis (FTA), and Failure Mode and Effect Analysis (FMEA) is provided and their integration feasibility is analyzed, followed by an application study in a shipyard located in Rio de Janeiro state, Brazil.

[1]  P. Bragatto,et al.  Updated Failure Rates and Risk Management in Process Industries , 2014 .

[2]  Loon Ching Tang,et al.  Fuzzy assessment of FMEA for engine systems , 2002, Reliab. Eng. Syst. Saf..

[3]  John D. Andrews,et al.  A fault tree analysis strategy using binary decision diagrams , 2002, Reliab. Eng. Syst. Saf..

[5]  David Coppit,et al.  Developing a low-cost high-quality software tool for dynamic fault-tree analysis , 2000, IEEE Trans. Reliab..

[6]  F. Rath.  Tools for developing a quality management program: proactive tools (process mapping, value stream mapping, fault tree analysis, and failure mode and effects analysis). , 2008, International journal of radiation oncology, biology, physics.

[7]  Min Xie,et al.  Optimum prioritisation and resource allocation based on fault tree analysis , 2000 .

[8]  Garcia,et al.  Uma abordagem via análise envoltória de dados para o estabelecimento de melhorias em segurança baseadas na FMEA A data envelopment analysis approach to safety improvements based on FMEA , 2013 .

[9]  Leonimer Flavio de Melo,et al.  ANÁLISE COMPARATIVA ENTRE METODOLOGIAS PARA ANÁLISE PRELIMINAR DE RISCO (APR) EM SERVIÇOS DE ENGENHARIA , 2013 .

[10]  Gestão da qualidade versus gestão por processos: metodologias unidas para dar maior competitividade à indústria , 2014 .

[11]  Murat Ozkok,et al.  Risk Assessment in Ship Hull Structure Production Using FMEA , 2014 .

[12]  Dagoberto Alves de Almeida,et al.  Metodologia integrada para mapeamento de falhas: uma proposta de utilização conjunta do mapeamento de processos com as técnicas FTA, FMEA e a análise crítica de especialistas , 2010 .

[13]  Yoshinobu Sato,et al.  Quantification of sequential failure logic for fault tree analysis , 2000, Reliab. Eng. Syst. Saf..

[14]  Arash Shahin,et al.  Integration of FMEA and the Kano model , 2004 .

[15]  Mahmood Shafiee,et al.  An FMEA-Based Risk Assessment Approach for Wind Turbine Systems: A Comparative Study of Onshore and Offshore , 2014 .

[16]  Sara Marcelino-Sádaba,et al.  Project risk management methodology for small firms , 2014 .

[17]  Dinesh Kumar,et al.  Modeling and analysing system failure behaviour using RCA, FMEA and NHPPP models , 2007 .

[18]  R. Yin.  Case Study Research: Design and Methods, 3rd Edition , 2002 .

[19]  T. Aven,et al.  Probability and Possibility‐Based Representations of Uncertainty in Fault Tree Analysis , 2013, Risk analysis : an official publication of the Society for Risk Analysis.

[20]  J. Gerring.  What Is a Case Study and What Is It Good for? , 2004, American Political Science Review.

[21]  José Luis Duarte Ribeiro,et al.  Integração do QFD e da FMEA por meio de uma sistemática para tomada de decisões no processo de desenvolvimento de produtos , 2013 .

[22]  José Márcio Ramos Fernandes,et al.  Proposta de um método para integração entre QFD e FMEA Proposal of a method to integrate QFD and FMEA , 2006 .

[23]  Jan Olhager,et al.  Lean and agile manufacturing: external and internal drivers and performance outcomes , 2009 .

[24]  K. Eisenhardt.  Building theories from case study research , 1989, STUDI ORGANIZZATIVI.

[25]  C. H. Lie,et al.  Fault Tree Analysis, Methods, and Applications ߝ A Review , 1985, IEEE Transactions on Reliability.

[26]  Jiju Antony,et al.  Confluence of six sigma, simulation and software development , 2005 .