Novel electromagnetic modeling approach of carbon fiber-reinforced polymer laminate for calculation of eddy currents and eddy current testing signals

Due to the heterogeneous nature and electric anisotropy, it is challenging to establish a numerical model to analyze the electromagnetic properties of multilayer carbon fiber-reinforced polymer (CFRP) laminate. In this study, we focus on the exploration of an effective electromagnetic modeling approach for calculation of eddy currents in CFRP laminate composite, as well as eddy current testing signals due to surface cracks. In order to prove the feasibility of modeling CFRP laminate with homogeneous anisotropic layers, the electrical parameters in the three directions are measured, and eddy current path in CFRP is investigated according to the measurement results. A finite element solver based on reduced magnetic vector potential ( A r ) formulation and edge elements is developed to enable the eddy current simulation of anisotropic CFRP material, which avoids matching the discretization of source coils with the rest of conductor mesh, and can easily solve the field continuity problem in the interface between two adjacent fiber layers of CFRP laminate. The A r formulation and way to calculate the eddy current testing signals are described. To validate of the developed simulation code, a comparison is conducted between the calculated signals and experimental results of thin-opening cracks in a CFRP test piece, which indicates the simulation code can predict eddy current testing signals with good precision.

[1]  Hiroyuki Fukutomi,et al.  Numerical evaluation of correlation between crack size and eddy current testing signal by a very fast simulator , 1998 .

[2]  M. L. Barton,et al.  New vector finite elements for three‐dimensional magnetic field computation , 1987 .

[3]  Harold A. Sabbagh,et al.  Electromagnetic interactions with an anisotropic slab , 1988 .

[4]  Gerhard Mook,et al.  Non-destructive characterisation of carbon-fibre-reinforced plastics by means of eddy-currents , 2001 .

[5]  Norbert Meyendorf,et al.  High-resolution eddy current sensor system for quality assessment of carbon fiber materials , 2010 .

[6]  Tony Roberts,et al.  Rapid growth forecast for carbon fibre market , 2007 .

[7]  Akira Todoroki,et al.  Measurement of orthotropic electric conductance of CFRP laminates and analysis of the effect on delamination monitoring with an electric resistance change method , 2002 .

[8]  Xavier E. Gros,et al.  An eddy current approach to the detection of damage caused by low-energy impacts on carbon fibre reinforced materials , 1995 .

[9]  Hideo Kobayashi,et al.  Application of Electric Potential Method to Smart Composite Structures for Detecting Delamination , 1995 .

[10]  Akihisa Kameari,et al.  Calculation of transient 3D eddy current using edge-elements , 1990 .

[11]  Akira Todoroki,et al.  The effect of number of electrodes and diagnostic tool for monitoring the delamination of CFRP laminates by changes in electrical resistance , 2001 .

[12]  Kenzo Miya,et al.  Three-Dimensional Simulation of Remote Field ECT using the Ar Method and a New Formula for Signal Calculation , 2005 .

[13]  W. F. Weldon,et al.  Eddy currents in anisotropic composites applied to pulsed machinery , 1996 .

[14]  H. Hahn,et al.  Investigation of temperature dependency of electrical resistance changes for structural management of graphite/polymer composite , 2011 .

[15]  Phil E. Irving,et al.  Fatigue damage characterization in carbon fibre composite materials using an electrical potential technique , 1998 .

[16]  Gilles Lubineau,et al.  On micro–meso relations homogenizing electrical properties of transversely cracked laminated composites , 2013 .

[17]  O. Bíró.  Edge element formulations of eddy current problems , 1999 .

[18]  Hiroyuki Fukutomi,et al.  Benchmark models of eddy current testing for steam generator tube: Experiment and numerical analysis , 1994 .

[19]  Karl Schulte,et al.  Non-destructive testing of FRP by d.c. and a.c. electrical methods , 2001 .

[20]  G. Lubineau,et al.  Cyclic hygrothermal aging of aircraft lightning protections: phenomenological overview. , 2012 .

[21]  Karl Schulte,et al.  Load and failure analyses of CFRP laminates by means of electrical resistivity measurements , 1989 .

[22]  Hiroyuki Fukutomi,et al.  Numerical evaluation of ECT impedance signal due to minute cracks , 1997 .

[23]  B. Ramdane,et al.  Interaction Between Electromagnetic Field and CFRP Materials: A New Multiscale Homogenization Approach , 2010, IEEE Transactions on Magnetics.

[24]  M. Feliachi,et al.  3-D Eddy Current Computation in Carbon-Fiber Reinforced Composites , 2009, IEEE Transactions on Magnetics.

[25]  A. Kameari.  Regularization on ill-posed source terms in FEM computation using two magnetic vector potentials , 2004, IEEE Transactions on Magnetics.

[26]  J. Fouladgar,et al.  Microscopic and Macroscopic Electromagnetic and Thermal Modeling of Carbon Fiber Reinforced Polymer Composites , 2010, IEEE Transactions on Magnetics.

[27]  A. Bossavit.  Whitney forms: a class of finite elements for three-dimensional computations in electromagnetism , 1988 .

[28]  M. Cacciola,et al.  Eddy Current Modeling in Composite Materials , 2009 .

[29]  Morelli,et al.  Magnetic susceptibility of carbon structures. , 1994, Physical review. B, Condensed matter.

[30]  Akira Todoroki,et al.  Electrical Resistance Change of Unidirectional CFRP Due to Applied Load , 2004 .

[31]  M. Feliachi,et al.  An Integro-Differential Model for 3-D Eddy Current Computation in Carbon Fiber Reinforced Polymer Composites , 2011, IEEE Transactions on Magnetics.

[32]  Gilles Lubineau,et al.  Improving electrical conductivity in polycarbonate nanocomposites using highly conductive PEDOT/PSS coated MWCNTs. , 2013, ACS applied materials & interfaces.

[33]  John Summerscales,et al.  Non‐destructive Testing of Fibre‐reinforced Plastics Composites, Vol. 2 , 1992 .

[34]  A. Kameari.  Solution of asymmetric conductor with a hole by FEM using edge-element , 1990 .