Design of a day tank glass furnace using a transient model and steady-state computation fluid dynamics

Abstract To design day tanks with energy efficiency and good operation standards, a detailed transient model that considers the melting, refining, cooling and working stages of the glass production process was developed. With the model, the required power input was determined, with glass coverage with batch (β) as parameter, for a furnace with a daily production of 1130 kg of soda-lime glass and 14 h for melting/refining. A detailed analysis of the energy balance with the model showed that during the daily cycle about 70% of the energy input is released with the flue gas. During the working stage most of the energy escapes through the doors. As the peak of energy consumption is during the refining process, the power requirement for this stage defines the global power requirement. Calculated energy efficiencies vary between 13% and 16% for β = 70% and 30% respectively. A steady state CFD simulation of the combustion chamber and glass tank shows that a side-fired burner configuration allows for lower gas velocities and temperatures close to the glass and the furnace walls while guaranteeing the same heat transfer characteristics to the glass than the more traditional end-fired (U-type) furnaces.

[1]  Guy Marin,et al.  Evaluation of high-emissivity coatings in steam cracking furnaces using a non-grey gas radiation model , 2008 .

[2]  Pierre Riedinger,et al.  First-principles simplified modelling of glass furnaces combustion chambers , 2008 .

[3]  Chenn Q. Zhou,et al.  Eulerian approach for multiphase flow simulation in a glass melter , 2005 .

[4]  U. N. Gaitonde,et al.  Model based energy benchmarking for glass furnace , 2007 .

[5]  Don W. Green,et al.  Perry's Chemical Engineers' Handbook , 2007 .

[6]  M. Modest.  Radiative heat transfer , 1993 .

[7]  R. Viskanta,et al.  Three-Dimensional Flow and Thermal Structure in Glass Melting Furnaces. Part I: Effect of the Net Heat Flux Distribution , 2002 .

[8]  E. A. Avellone,et al.  Marks' Standard Handbook for Mechanical Engineers , 1916 .

[9]  Bart Merci,et al.  Gray/nongray gas radiation modeling in steam cracker CFD calculations , 2007 .

[10]  H. Hottel,et al.  Mathematical and Experimental Modeling of the Circulation Patterns in Glass Melts , 1972 .

[11]  C. Iung,et al.  Glass furnace, simplified modelling for control and real time simulation , 2004, 2004 IEEE International Symposium on Industrial Electronics.

[12]  Maria A. Founti,et al.  Assessment of simplified thermal radiation models for engineering calculations in natural gas-fired furnace , 2007 .

[13]  D. Ibarra,et al.  Diseño de un horno de operación periódica tipo day tank de uso en pequeñas y medianas empresas de vidrio , 2011 .

[14]  N. S. Vlachos,et al.  Natural convection in rectangular tanks heated locally from below , 2004 .

[15]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[16]  Andrés Amell,et al.  Numerical simulation of the flow streams behavior in a self-regenerative crucible furnace , 2010 .

[18]  George N Walton,et al.  Calculation of obstructed view factors by adaptive integration , 2002 .

[19]  Sergei Sazhin,et al.  The P-1 model for thermal radiation transfer: advantages and limitations , 1996 .

[20]  Gilbert F. Froment,et al.  The coupled simulation of heat transfer and reaction in a pyrolysis furnace , 1988 .

[21]  C. Madivate.  Calculation of the Theoretical Energy Requirement for Melting Technical Silicate Glasses , 1998 .

[22]  Modelling of glass melting industrial process , 1993 .

[23]  K. Khoshmanesh,et al.  Numerical simulation and experimental analysis of an industrial glass melting furnace , 2008 .