Melt granulation using a twin-screw extruder: a case study.

The purpose of this study was to use a twin-screw extruder for melt granulation. Polyethylene glycols (PEG 400 and 4000) were used as binders for the development of a drinking water formulation with immediate drug release. The effect of drug content, PEG 400/4000-ratio, surfactant (type and concentration) and granulation temperature on granule properties and dissolution characteristics was determined. The granulation temperature had an important influence on the granule formation. High yield (95% of the granules <1400 microm) was obtained only at a temperature near the melting point of PEG 4000. During granulation the drug of BCS class II was finely dispersed in the PEGs, creating a micro-environment around the drug particles enhancing the dissolution rate. To obtain complete drug release within 10 min for a formulation containing 10% drug, the addition of 2% (w/w) surfactant (polysorbate 80 or Cremophor RH40) was required. At a higher drug content (20%), the PEG 4000 concentration had to be increased to 20% to improve granule properties and 4% polysorbate 80 was required to obtain 100% drug release. X-ray diffractograms showed distinct peaks of crystalline drug, the crystallinity of the drug did not change after 50 days, independent of the storage conditions.

[1]  Torben Schaefer,et al.  Effects of droplet size and type of binder on the agglomerate growth mechanisms by melt agglomeration in a fluidised bed. , 2002, European journal of pharmaceutical sciences : official journal of the European Federation for Pharmaceutical Sciences.

[2]  J. Remon,et al.  Matrix pellets based on the combination of waxes, starches and maltodextrins , 1996 .

[3]  T. Schaefer,et al.  The effect of droplet size and powder particle size on the mechanisms of nucleation and growth in fluid bed melt agglomeration. , 2002, International journal of pharmaceutics.

[4]  P. Holm,et al.  Extrusion of an Effervescent Granulation with a Twin Screw Extruder, Baker Perkins MPF 50 D. Influence on Intragranular Porosity and Liquid Saturation , 1988 .

[5]  M. J. Gamlen,et al.  Continuous Extrusion Using a Raker Perkins MP50 (Multipurpose) Extruder , 1986 .

[6]  C Vervaet,et al.  Twin screw granulation as a simple and efficient tool for continuous wet granulation. , 2004, International journal of pharmaceutics.

[7]  Torben Schæfer,et al.  Melt pelletization in a high shear mixer. VIII. Effects of binder viscosity , 1996 .

[8]  Raymond C Rowe,et al.  Handbook of Pharmaceutical Excipients , 1994 .

[9]  H. Kristensen,et al.  Melt pelletization in a high shear mixer. IV. Effects of process variables in a laboratory scale mixer , 1993 .

[10]  T. Schæfer Melt pelletization in a high shear mixer VI. Agglomeration of a cohesive powder , 1996 .

[11]  J. Remon,et al.  Influence of processing on the characteristics of matrix pellets based on microcrystalline waxes and starch derivatives , 1997 .

[12]  H Leuenberger,et al.  New trends in the production of pharmaceutical granules: batch versus continuous processing. , 2001, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.

[13]  N. O. Lindberg,et al.  Extrusion of an Effervescent Granulation with a Twin Screw Extruder, Baker Perkins MPF 50 D , 1987 .

[14]  Torben Schæfer,et al.  Melt pelletization in a high shear mixer. IX. Effects of binder particle size , 1996 .

[15]  T. Schæfer,et al.  Melt pelletization in a high shear mixer. VII. Effects of product temperature , 1996 .

[16]  H. Kristensen,et al.  Melt pelletization in a high shear mixer. V. Effects of apparatus variables , 1993 .

[17]  Torben Schæfer,et al.  Melt Granulation in A Laboratory Scale High Shear Mixer , 1990 .