Earth-based additive manufacturing: A field-oriented methodology for evaluating material printability

The recent convergence of earth construction with technology focuses on additive manufacturing using extrudable earth-based materials. The printability of these materials can be defined by their pumpability, extrudability, and buildability. We present a field-oriented methodology for the design of printable local mixtures suitable for various printers. Three tests were defined to characterize the flowability, pumpability and extrudability, and buildability of such materials in their fresh or ‘green’ state, and used to optimize the workability of a sample material for printability. Based on the outcomes, two indices are proposed for the classification and control of the printability of earthen mixtures: flowability and green strength. Our results demonstrate that adjusting water content for consistency and adjusting plasticity for cohesiveness are both vital for tuning printability, although the necessary modifications can negatively affect the material's strength in its hardened state; incorporating cellulose microfibres can counter this by increasing flowability, plasticity, and compressive strength.

[1]  E. Ferretti,et al.  Rice-Husk Shredding as a Means of Increasing the Long-Term Mechanical Properties of Earthen Mixtures for 3D Printing , 2021, Materials.

[2]  Ulrich Knaack,et al.  Ten questions concerning the potential of digital production and new technologies for contemporary earthen constructions , 2021 .

[3]  Wassim Jabi,et al.  3D printing system for earth-based construction: Case study of cob , 2021 .

[4]  K. L. Bar-Sinai,et al.  Robotic tools, native matter: workflow and methods for geomaterial reconstitution using additive manufacturing , 2021, Architectural Science Review.

[5]  S. Geoffroy,et al.  Effects of organic admixtures on the fresh and mechanical properties of earth-based plasters , 2021 .

[6]  E. Keita,et al.  Yield stress measurement for earth-based building materials: the weighted plunger test , 2021 .

[7]  Erik Schlangen,et al.  Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture , 2020, Cement and Concrete Research.

[8]  C. Tribout,et al.  Is stabilization of earth bricks using low cement or lime contents relevant? , 2020, Construction and Building Materials.

[9]  Rachel Ben-alon,et al.  Natural Buildings: Integrating Earthen Building Materials and Methods Into Mainstream Construction , 2020 .

[10]  Un-Habitat,et al.  Rethinking Building Practices: Interventions in building design, constructions, cost effectiveness and resource efficiency. , 2020 .

[11]  Vivian Loftness,et al.  Integrating Earthen Building Materials and Methods into Mainstream Construction Using Environmental Performance Assessment and Building Policy , 2019, Journal of Green Building.

[12]  Wassim Jabi,et al.  Negotiated matter: a robotic exploration of craft-driven innovation , 2019, Architectural Science Review.

[13]  Ming Jen Tan,et al.  Mechanical properties and deformation behaviour of early age concrete in the context of digital construction , 2019, Composites Part B: Engineering.

[14]  3D Printing of Concrete , 2019 .

[15]  Eric Courteille,et al.  3D printing of earth-based materials: Processing aspects , 2018 .

[16]  F. Winnefeld,et al.  A fresh look at dense clay paste: Deflocculation and thixotropy mechanisms , 2018 .

[17]  Jean-Emmanuel Aubert,et al.  Plant aggregates and fibers in earth construction materials: A review , 2016 .

[18]  J. Morel,et al.  How Properties of Kenaf Fibers from Burkina Faso Contribute to the Reinforcement of Earth Blocks , 2015, Materials.

[19]  Gernot Minke,et al.  Building with Earth , 2005 .

[20]  Bui,et al.  Testing and Characterisation of Earth-based Building Materials and Elements , 2022, RILEM State-of-the-Art Reports.

[21]  Viktor Mechtcherine,et al.  Studying the Printability of Fresh Concrete for Formwork-Free Concrete Onsite 3D Printing Technology (CONPrint3D) , 2019, 3D Concrete Printing Technology.

[22]  A. Perrot.  3D printing of concrete : state of the art and challenges of the digital construction revolution , 2019 .

[23]  Ronald Rael,et al.  Developing Concrete Polymer Building Components for 3D Printing , 2011, ACADIA proceedings.

[24]  Achim Menges,et al.  Integration through Computation: Proceedings of the 31st Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) , 2011 .