Electronically probed measurements of MEMS geometries

Measurement of microelectromechanical systems (MEMS) geometry is critical for device design and simulation, material property extraction, and post-fabrication trimming. In this paper electrostatically driven laterally resonant comb-drive test structures with prescribed changes in spring width are used to ascertain systematic variations in process offsets (edge biases) and sidewall angles. The technique is both in situ and nondestructive. An analytical model for the resonant frequency, tuned with three-dimensional (3-D) simulations using MEMCAD, includes effects of a distributed mass, residual stress, and compliant supports. The model is corroborated by 3-D numerical simulations to validate the extraction approach. Fits of this model to experimental data determine the offset and sidewall angle of polysilicon devices fabricated by the Multi-User MEMS Processes of the Microelectronics Center of North Carolina, Research Triangle Park, NC.

[1]  Fabien Mieyeville,et al.  Automatic evaluation of a sensor's geometrical parameters , 1999, Design, Test, Integration, and Packaging of MEMS/MOEMS.

[2]  Erik R. Deutsch.  Development of calibration standards for accurate measurement of geometry in microelectromechanical systems , 1998 .

[3]  Christopher C. T. Nguyen,et al.  High-order micromechanical electronic filters , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[4]  B. Jensen,et al.  IMAP: Interferometry for Material Property Measurement in MEMS , 1999 .

[5]  Zhijian Li,et al.  New methods for measuring mechanical properties of thin films in micromachining: Beam pull-in voltage (VPI) method and long beam deflection (LBD) method , 1995 .

[6]  A. Steckenborn,et al.  Determination of Young's moduli of micromechanical thin films using the resonance method , 1992 .

[7]  Fabien Mieyeville,et al.  Automatic evaluation of sensors geometrical parameters , 1999 .

[8]  Brian D. Jensen,et al.  Interferometry of actuated microcantilevers to determine material properties and test structure nonidealities in MEMS , 2001 .

[9]  H. Tilmans.  Micro-mechanical sensors using encapsulated built-in resonant strain gauges , 1991 .

[10]  William C. Tang,et al.  Electrostatic Comb Drive for Resonant Sensor and Actuator Applications , 1990 .

[11]  R. Mullen,et al.  Mechanical properties of thick, surface micromachined polysilicon films , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.

[12]  Robert L. Mullen,et al.  Monte Carlo simulation of effective elastic constants of polycrystalline thin films , 1997 .

[13]  R. L. Edwards,et al.  Measurements of Young's modulus, Poisson's ratio, and tensile strength of polysilicon , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[14]  J. Bustillo,et al.  Surface micromachining for microelectromechanical systems , 1998, Proc. IEEE.

[15]  S. Senturia,et al.  Pull-in time dynamics as a measure of absolute pressure , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[16]  Jan-Åke Schweitz,et al.  mechanical Characterization of Thin Films by Micromechanical Techniques , 1992 .

[17]  Stephen D. Senturia,et al.  The effect of release-etch holes on the electromechanical behaviour of MEMS structures , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[18]  B. Culshaw,et al.  Measurement of the mechanical properties of silicon microresonators , 1991 .

[19]  D. W. Burns,et al.  Mechanical properties of fine grained polysilicon-the repeatability issue , 1988, IEEE Technical Digest on Solid-State Sensor and Actuator Workshop.

[20]  M. Schmidt,et al.  Monitoring plasma over-etching of Wafer-bonded Microstructures , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[21]  R. Howe,et al.  Young's Modulus Of In Situ Phosphorus-doped Polysilicon , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[22]  Robert W. Dutton,et al.  Comprehensive Static Characterization of Vertical Electrostatically Actuated Polysilicon Beams , 1999, IEEE Des. Test Comput..

[23]  K. Breuer,et al.  Gaseous slip flow in long microchannels , 1997 .

[24]  K. Najafi,et al.  A novel technique and structure for the measurement of intrinsic stress and Young's modulus of thin films , 1989, IEEE Micro Electro Mechanical Systems, , Proceedings, 'An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots'.

[25]  Robert Amantea,et al.  Resistive damping of pulse-sensed capacitive position sensors , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[26]  Herbert F. Wang,et al.  Single Crystal Elastic Constants and Calculated Aggregate Properties. A Handbook , 1971 .

[27]  H. J. Mcskimin.  Measurement of Elastic Constants at Low Temperatures by Means of Ultrasonic Waves–Data for Silicon and Germanium Single Crystals, and for Fused Silica , 1953 .

[28]  Khalil Najafi,et al.  Electronic Determination of the Modulus of Elasticity and Intrinsic Stress of Thin Films using Capacitive Bridges , 1992 .

[29]  Stephen D. Senturia,et al.  Mechanical Properties of Microsensor Materials: How to Deal with the Process Dependences? , 1991 .

[30]  S. Senturia,et al.  M-TEST: A test chip for MEMS material property measurement using electrostatically actuated test structures , 1997 .

[31]  K. Petersen.  Dynamic micromechanics on silicon: Techniques and devices , 1978, IEEE Transactions on Electron Devices.

[32]  Alan V. Oppenheim,et al.  Signals & systems (2nd ed.) , 1996 .

[33]  Udo Sobe,et al.  New designs of micromachined vibrating rate gyroscopes with decoupled oscillation modes , 1998 .

[34]  S. Senturia,et al.  Speed-energy optimization of electrostatic actuators based on pull-in , 1999 .

[35]  Tamal Mukherjee,et al.  Automated optimal synthesis of microresonators , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[36]  R. Howe,et al.  Characterization of Thin Films using Micromechanical Structures , 1992 .