Modeling the influence of bubble pressure on grain boundary separation and fission gas release

Grain boundary (GB) separation as a mechanism for fission gas release (FGR), complementary to gas bubble interlinkage, has been experimentally observed in irradiated light water reactor fuel. However there has been limited effort to develop physics-based models incorporating this mechanism for the analysis of FGR. In this work, a computational study is carried out to investigate GB separation in UO2 fuel under the effect of gas bubble pressure and hydrostatic stress. A non-dimensional stress intensity factor formula is obtained through 2D axisymmetric analyses considering lenticular bubbles and Mode-I crack growth. The obtained functional form can be used in higher length-scale models to estimate the contribution of GB separation to FGR.

[1]  H. Bunge.  Texture Analysis in Materials Science , 1982 .

[2]  M. Mogensen,et al.  An experimental study of the distribution of retained xenon in transient-tested UO2 fuel , 1993 .

[3]  J. Newman.  An improved method of collocation for the stress analysis of cracked plates with various shaped boundaries , 1971 .

[4]  Dan G. Cacuci,et al.  Handbook of Nuclear Engineering , 2010 .

[5]  J. Rest,et al.  The mechanistic prediction of transient fission-gas release from LWR fuel☆☆☆ , 1980 .

[6]  Hiroshi Tada,et al.  The stress analysis of cracks handbook , 2000 .

[7]  Yang-Hyun Koo,et al.  Analysis of fission gas release and gaseous swelling in UO , 2000 .

[8]  Marc Hou,et al.  Comparison of interatomic potentials for UO2. Part I: Static calculations , 2007 .

[9]  Toshiaki Kogai,et al.  Modelling of fission gas release and gaseous swelling of light water reactor fuels , 1997 .

[10]  E. Riks.  The Application of Newton's Method to the Problem of Elastic Stability , 1972 .

[11]  W. Knauss,et al.  Propagation of a crack under general, in-plane tension , 1972 .

[12]  W. Hering.  The kwu fission gas release model for lwr fuel rods , 1983 .

[13]  Mujid S. Kazimi,et al.  On the significance of modeling nuclear fuel behavior with the right representation of physical phenomena , 2011 .

[14]  G. Sih.  Strain-energy-density factor applied to mixed mode crack problems , 1974 .

[15]  M. S. Veshchunov,et al.  Modelling of grain face bubbles coalescence in irradiated UO2 fuel , 2008 .

[16]  M. Mogensen,et al.  Concerning the development of grain face bubbles and fission gas release in UO2 fuel , 1988 .

[17]  R. Barsoum.  On the use of isoparametric finite elements in linear fracture mechanics , 1976 .

[18]  Donald R. Olander,et al.  Fundamental Aspects of Nuclear Reactor Fuel Elements , 1976 .

[19]  Donald R. Olander,et al.  Fundamental aspects of nuclear reactor fuel elements : prepared for the Division of Reactor Development and Demonstration, Energy Research and Development Administration , 1976 .

[20]  I. J. Hastings,et al.  Fission gas release from power-ramped UO2 fuel , 1986 .

[21]  R. J. White,et al.  The development of grain-face porosity in irradiated oxide fuel , 2004 .

[22]  J. Rice.  A path-independent integral and the approximate analysis of strain , 1968 .

[23]  J. Rest.  An improved model for fission product behavior in nuclear fuel under normal and accident conditions , 1984 .

[24]  Zenon Mróz,et al.  A non-local stress failure condition for structural elements under multiaxial loading , 1995 .

[25]  R. J. White,et al.  A new fission-gas release model , 1983 .

[26]  Yang-Hyun Koo,et al.  Cosmos: A computer code to analyze LWR UO2 and MOX fuel up to high burnup , 1999 .

[27]  M. Mogensen,et al.  On the Rate Determining Step in Fission Gas Release from High Burn-up Water Reactor Fuel during Power Transients , 1987 .

[28]  Shinji Kashibe,et al.  Fission Gas Release during Post Irradiation Annealing of BWR Fuels , 1990 .

[29]  John R. Rice,et al.  ON THE RELATIONSHIP BETWEEN CRITICAL TENSILE STRESS AND FRACTURE TOUGHNESS IN MILD STEEL , 1973 .

[30]  J. G. Morgan,et al.  Fission Density, Burnup, and Temperature Effects on Fission-Gas Release From UO2 , 1969 .