Vertical Light-Emitting Diode Fabrication by Controlled Spalling

A fracture-based layer transfer technique referred to as controlled spalling was used to separate a conventional InGaN/GaN multiple quantum well light-emitting diode (LED) structure from a 50 mm sapphire wafer enabling the formation of vertical spalled LEDs (SLEDs). A 25-µm-thick tensile Ni layer was electrodeposited on the surface of the wafer, followed by the application of a polyimide tape layer. By mechanically guiding the tape layer, a 3-µm-thick layer of the LED epitaxy was removed. Transmission electron microscopy imaging indicated that spalling preserved the quality of the epitaxial layers, and electroluminescence verifies the operation of the SLED.

[1]  S. Denbaars,et al.  Increase in the extraction efficiency of GaN-based light-emitting diodes via surface roughening , 2004 .

[2]  M. D. Thouless,et al.  The edge cracking and spalling of brittle plates , 1987 .

[3]  Krüger,et al.  Strain-related phenomena in GaN thin films. , 1996, Physical review. B, Condensed matter.

[4]  C. Chu,et al.  High brightness GaN vertical light emitting diodes on metal alloyed substrate for general lighting application , 2007 .

[5]  M. Craford,et al.  Status and Future of High-Power Light-Emitting Diodes for Solid-State Lighting , 2007, Journal of Display Technology.

[6]  Olivier Durand,et al.  Use of ZnO thin films as sacrificial templates for metal organic vapor phase epitaxy and chemical lift-off of GaN , 2007 .

[7]  C. Bayram,et al.  Comprehensive study of blue and green multi-quantum-well light-emitting diodes grown on conventional and lateral epitaxial overgrowth GaN , 2009 .

[8]  J. Ager,et al.  Hardness and fracture toughness of bulk single crystal gallium nitride , 1996 .

[9]  Takashi Mukai,et al.  High‐brightness InGaN/AlGaN double‐heterostructure blue‐green‐light‐emitting diodes , 1994 .

[10]  Davood Shahrjerdi,et al.  Ultralight High‐Efficiency Flexible InGaP/(In)GaAs Tandem Solar Cells on Plastic , 2013 .

[11]  Takashi Mukai,et al.  High‐power InGaN/GaN double‐heterostructure violet light emitting diodes , 1993 .

[12]  J. A. Ott,et al.  Kerf-Less Removal of Si, Ge, and III–V Layers by Controlled Spalling to Enable Low-Cost PV Technologies , 2011, IEEE Journal of Photovoltaics.

[13]  Y. S. Wu,et al.  Effects of laser sources on the reverse-bias leakages of laser lift-off GaN-based light-emitting diodes , 2007 .

[14]  J. Baek,et al.  Doping selective lateral electrochemical etching of GaN for chemical lift-off , 2009 .

[15]  Y. Kiang,et al.  Photoelectrochemical Liftoff of Patterned Sapphire Substrate for Fabricating Vertical Light-Emitting Diode , 2012, IEEE Photonics Technology Letters.

[16]  J. Ha,et al.  Leakage current improvement of nitride-based light emitting diodes using CrN buffer layer and its vertical type application by chemical lift-off process , 2009 .

[17]  Davood Shahrjerdi,et al.  Layer transfer by controlled spalling , 2013 .

[18]  Zhigang Suo,et al.  Steady-state cracking in brittle substrates beneath adherent films , 1989 .

[19]  Davood Shahrjerdi,et al.  Extremely flexible nanoscale ultrathin body silicon integrated circuits on plastic. , 2013, Nano letters.

[20]  William S. Wong,et al.  Damage-free separation of GaN thin films from sapphire substrates , 1998 .