A comprehensive design and rating study of evaporative coolers and condensers. Part I. Performance evaluation

Abstract The mathematical models of evaporative fluid coolers and evaporative condensers are studied in detail to perform a comprehensive design and rating analysis. The mathematical models are validated using experimental as well as numerical data reported in the literature. These models are integrated with the fouling model presented in an earlier paper, using the experimental data on tube fouling. In this paper, we use the fouling model to investigate the risk based thermal performance of these evaporative heat exchangers. It is demonstrated that thermal effectiveness of the evaporative heat exchangers degrades significantly with time indicating that, for a low risk level ( p =0.01), there is about 66.7% decrease in effectiveness for the given fouling model. Furthermore, it is noted that there is about 4.7% increase in outlet process fluid temperature of the evaporative fluid cooler. Also, a parametric study is performed to evaluate the effect of elevation and mass flow rate ratio on typical performance parameters such as effectiveness for rating calculations while surface area for design calculations.

[1]  Syed M. Zubair,et al.  A comprehensive design and performance evaluation study of counter flow wet cooling towers , 2004 .

[2]  N. V. Tovaras,et al.  Investigation of heat, mass transfer and fluid flow characteristics in evaporative condensers☆ , 1984 .

[3]  M. Shah.  A general correlation for heat transfer during film condensation inside pipes , 1979 .

[4]  S. Tezuka,et al.  Performance of an evaporative cooler , 1977 .

[5]  Wojciech Zalewski,et al.  Optimization of evaporative fluid coolers , 2000 .

[6]  E. Velasco Gómez,et al.  Simulation model of an indirect evaporative cooler , 1998 .

[7]  Wojciech Zalewski,et al.  Mathematical model of heat and mass transfer processes in evaporative fluid coolers , 1997 .

[8]  I. C. Finlay,et al.  Evaporative cooling of tube banks , 1984 .

[9]  John C. Chato,et al.  Laminar condensation inside horizontal and inclined tubes , 1960 .

[10]  D. Baker,et al.  a comprehensive approach to the analysis of cooling tower performance , 1961 .

[11]  R. L. Webb,et al.  Algorithms for performance simulation of cooling towers, evaporative condensers, and fluid coolers , 1984 .

[12]  Boris Halasz,et al.  A general mathematical model of evaporative cooling devices , 1998 .

[13]  Wolfgang Leidenfrost,et al.  Evaporative Cooling and Heat Transfer Augmentation Related to Reduced Condenser Temperatures , 1982 .

[14]  W. Zalewski.  Mathematical model of heat and mass transfer processes in evaporative condensers , 1993 .

[15]  Hisashi Miyashita,et al.  Characteristics and Methods of Thermal Design of Evaporative Cooler , 1968 .

[16]  Syed M. Zubair,et al.  The impact of fouling on performance evaluation of evaporative coolers and condensers , 2005 .

[17]  Tianshou Zhao,et al.  A parametric study of an indirect evaporative air cooler , 1998 .

[18]  Hisham Ettouney,et al.  Performance of evaporative condensers , 2001 .

[19]  R. L. Webb,et al.  A unified theoretical treatment for thermal analysis of cooling towers, evaporative condensers, and fluid coolers , 1984 .

[20]  J. W. Sutherland,et al.  Analysis of Mechanical-Draught Counterflow Air/Water Cooling Towers , 1983 .

[21]  Edoardo Gianolio,et al.  Heat Transfer Coefficients and Pressure Drops for Air Coolers with Different Numbers of Rows Under Induced and Forced Draft , 1981 .