Aerodynamic analysis of conical diffusers operating with air and supercritical carbon dioxide

Abstract The design of efficient supercritical carbon dioxide (S-CO 2 ) turbomachinery to be used for power generation (and also for CO 2 capture facilities) has gained interest in recent years due to the compactness and good performance of the S-CO 2 recuperative Brayton cycle in nuclear, waste heat and solar applications. Presently, in addition to a large amount of theoretical work focused on the analysis and optimisation of the system, there are even some prototypes of centrifugal compressors running on experimental facilities like, for instance, the pilot plant at SANDIA National Laboratories engineered by Barber Nichols Inc. Nevertheless, the performance of this experimental unit is far from an equivalent air/gas turbomachinery, say 80% compressor efficiency, mainly due to a lack of knowledge about the particular behaviour of this working fluid. The need to research these aspects of turbomachinery design has already been identified by the scientific and industrial communities. This work aims to provide more information about diffusion of S-CO 2 flows in conical ducts based on the experimental work on air diffusers carried out from the sixties to the eighties (in particular the test conducted by Dolan and Runstadler in 1973). Following a similar approach but by means of numerical analysis (CFD) rather than tests, the work presented here provides a comparison of the expected performance when S-CO 2 is used. It is observed that this new working fluid is likely to enhance the pressure rise capability while, at the same time, contribute to reducing the total pressure losses with respect to air. The work commences with a brief introduction to the fundamentals of conical diffusers followed by a discussion on the methodology, mesh size and convergence criteria. Then the most relevant geometric and aerodynamic parameters are assessed prior to providing some conclusions about the expected impact of using S-CO 2 on a radial compressor.

[1]  W. Wakeham,et al.  The Viscosity of Carbon Dioxide , 1998 .

[2]  Enrico Rinaldi,et al.  Computational Fluid Dynamics of a Radial Compressor Operating With Supercritical CO2 , 2012 .

[3]  D. Japikse.  Centrifugal compressor design and performance , 1996 .

[4]  David Gordon Wilson,et al.  The design of high-efficiency turbomachinery and gas turbines , 1984 .

[5]  Pericles Pilidis,et al.  A Semiclosed-Cycle Gas Turbine With Carbon Dioxide–Argon as Working Fluid , 1997 .

[6]  John H. Weare,et al.  An equation of state for the CH4-CO2-H2O system: I. Pure systems from 0 to 1000°C and 0 to 8000 bar , 1992 .

[7]  W. Wagner,et al.  A New Equation of State for Carbon Dioxide Covering the Fluid Region from the Triple‐Point Temperature to 1100 K at Pressures up to 800 MPa , 1996 .

[8]  J. R. Henry,et al.  SUMMARY OF SUBSONIC-DIFFUSER DATA , 1956 .

[9]  W. Wakeham,et al.  The Transport Properties of Carbon Dioxide , 1990 .

[10]  Jun Shao,et al.  Quantitative V&V of CFD simulations and certification of CFD codes , 2006 .

[11]  Pericles Pilidis,et al.  Design of a Semiclosed-Cycle Gas Turbine With Carbon Dioxide–Argon as Working Fluid , 1998 .

[12]  F. Dolan,et al.  Pressure recovery performance of conical diffusers at high subsonic Mach numbers , 1973 .

[13]  Hiroshige Kikura,et al.  Research on Flow Characteristics of Supercritical CO2 Axial Compressor Blades by CFD Analysis , 2010 .

[14]  Yong Wang,et al.  Compressor Design for the Supercritical CO2 Brayton Cycle , 2004 .