Shear Fatigue Analysis of SAC-Bi Solder Joint Exposed to Varying Stress Cycling Conditions

Sn–Ag–Cu (SAC) solder alloys are frequently used in electronic assemblies, and their fatigue resistance under various stress cycles is a significant factor that influences the reliability of electronics. Three distinct SAC-based solder joints (SAC305, SAC-Q, and SAC-R) were examined under various stress amplitude cycling and ambient temperature conditions. The stress on individual solder joints alternates between mild stress (MS) and harsh stress (HS) until complete failure. The hysteresis loop was investigated and compared under various stress amplitude cycles. In addition, the morphology and microstructure of the solder joints were analyzed. The results revealed that SAC-Q, with high Bi and Ag content, demonstrated superior fatigue resistance compared with SAC305 and SAC-R under varying stress amplitude conditions. The inelastic work increased with each change between the MS and HS cycles. SAC-Q exhibited solid solution and precipitate hardening mechanisms through the presence of bismuth (Bi) and silver (Ag) in the tin (Sn) lattice. At the same time, SAC305 showed Ag3Sn precipitates hardening, whereas SAC-R, with no Ag, demonstrated solid solution hardening exclusively. Different failure mechanisms were observed depending on the alloy composition and strain rate. SAC305 and SAC-R exhibited ductile failure. However, SAC-Q experienced an interfacial fracture. Excessive Bi may lead to the embrittlement of solder joints and a change in the failure mechanisms during mechanical testing.

[1]  A. Alahmer,et al.  Analysis and Modeling of Aged SAC-Bi Solder Joints Subjected to Varying Stress Cycling Conditions , 2023, Materials.

[2]  A. Alahmer,et al.  Assessing the SAC305 Solder Joint Fatigue in BGA Assembly Using Strain-Controlled and Stress-Controlled Approaches , 2022, Journal of Electronic Packaging.

[3]  A. Alahmer,et al.  The Effect of Micro-Alloying and Surface Finishes on the Thermal Cycling Reliability of Doped SAC Solder Alloys , 2022, Materials.

[4]  A. Alahmer,et al.  Shear and Fatigue Properties of Lead-Free Solder Joints: Modeling and Microstructure Analysis , 2022, Journal of Electronic Packaging.

[5]  Yaocheng Zhang,et al.  Effect of bonding time on the microstructure and shear property of Cu/SAC-15Ag/Cu 3D package solder joint fabricated by TLP , 2021, Journal of Materials Science: Materials in Electronics.

[6]  Gang Wang,et al.  Interfacial microstructure evolution and properties of Sn-0.3Ag-0.7Cu–xSiC solder joints , 2021 .

[7]  P. Dixit,et al.  A review of intermetallic compound growth and void formation in electrodeposited Cu–Sn Layers for microsystems packaging , 2021, Journal of Materials Science: Materials in Electronics.

[8]  Haitao Ma,et al.  Effect of the degree of supercooling on growth mechanism of Cu6Sn5 in pure Sn/Cu solder joint , 2021, Journal of Materials Science: Materials in Electronics.

[9]  Dania Bani Hani,et al.  Effect of Aging on the Fatigue Life and Shear Strength of SAC305 Solder Joints in Actual Setting Conditions , 2019, 2019 18th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (ITherm).

[10]  R. Coyle,et al.  Pb-Free Solder Joint Thermo-Mechanical Modeling: State of the Art and Challenges , 2018, JOM.

[11]  M. Celikin,et al.  Effect of Bi Additions on the Creep Behaviour of SAC Solder Alloys , 2018, Journal of Electronic Materials.

[12]  K. Kanlayasiri,et al.  Property alterations of Sn-0.6Cu-0.05Ni-Ge lead-free solder by Ag, Bi, In and Sb addition , 2018, Transactions of Nonferrous Metals Society of China.

[13]  Stuart D. McDonald,et al.  The effects of precipitation strengthening and solid solution strengthening on strain rate sensitivity of lead-free solders: Review , 2018, Microelectron. Reliab..

[14]  Richard J. Coyle,et al.  Thermal Fatigue Evaluation of Pb-Free Solder Joints: Results, Lessons Learned, and Future Trends , 2015 .

[15]  P. Borgesen.  Microstructurally Adaptive Constitutive Relations and Reliability Assessment Protocols for Lead Free Solder , 2015 .

[16]  A. A. El-Daly,et al.  Development of new multicomponent Sn–Ag–Cu–Bi lead-free solders for low-cost commercial electronic assembly , 2015 .

[17]  Samjid H. Mannan,et al.  A review: On the development of low melting temperature Pb-free solders , 2014, Microelectron. Reliab..

[18]  Peter Borgesen,et al.  On the Assessment of the Life of SnAgCu Solder Joints in Cycling With Varying Amplitudes , 2013, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[19]  Suhana Mohd Said,et al.  A review on effect of minor alloying elements on thermal cycling and drop impact reliability of low‐Ag Sn‐Ag‐Cu solder joints , 2012 .

[20]  S. Xue,et al.  Review Article: Effect of alloying elements on properties and microstructures of SnAgCu solders , 2010 .

[21]  Cong-qian Cheng,et al.  Kinetics of intermetallic compound layers and shear strength in Bi-bearing SnAgCu/Cu soldering couples , 2009 .

[22]  Chris Bailey,et al.  Effect of adding 1 wt% Bi into the Sn–2.8Ag–0.5Cu solder alloy on the intermetallic formations with Cu-substrate during soldering and isothermal aging , 2006 .

[23]  Y. Miyashita,et al.  Low-cycle fatigue behavior of Sn-Ag, Sn-Ag-Cu, and Sn-Ag-Cu-Bi lead-free solders , 2002 .

[24]  R. Erich,et al.  Shear testing and failure mode analysis for evaluation of BGA ball attachment , 1999, Twenty Fourth IEEE/CPMT International Electronics Manufacturing Technology Symposium (Cat. No.99CH36330).

[25]  M. Otsuka,et al.  Effect of bismuth on the isothermal fatigue properties of Sn-3.5mass%Ag solder alloy , 1998 .