On the selection of Ti–Cu alloys for thixoforming processes: phase diagram and microstructural evaluation

[1]  R. Pesci,et al.  Microstructure investigation and flow behavior during thixoextrusion of M2 steel grade , 2015 .

[2]  S. Zaefferer,et al.  Theory and application of electron channelling contrast imaging under controlled diffraction conditions , 2014 .

[3]  Renbo Song,et al.  Evolution of microstructure and mechanical properties for 9Cr18 stainless steel during thixoforming , 2014 .

[4]  Yong-qing Zhao,et al.  Influence of semisolid forging ratio on the microstructure and mechanical properties of Ti14 alloy , 2013, International Journal of Minerals, Metallurgy, and Materials.

[5]  E. J. Zoqui,et al.  Thixoformability of hypoeutectic gray cast iron , 2012 .

[6]  W. Jianfeng,et al.  Microscopic Characterization of Semi-Solid Ti14 Alloy , 2012 .

[7]  M. Z. Omar,et al.  Microstructural investigations of XW-42 and M2 tool steels in semi-solid zones via direct partial remelting route , 2011 .

[8]  Yongnan Chen,et al.  Microstructure evolution and grain growth behavior of Ti14 alloy during semi-solid isothermal process , 2011 .

[9]  D. Apelian,et al.  Commercial AM60 alloy for semisolid processing: Alloy optimization and thermodynamic analysis , 2010 .

[10]  B. Amin-ahmadi,et al.  Semisolid structure for M2 high speed steel prepared by cooling slope , 2010 .

[11]  Shiping Wu,et al.  Research on Mould Filling and Solidification of Titanium Alloy in Vertical Centrifugal Casting , 2010 .

[12]  Yu Zhao,et al.  Effect of semi-solid forging temperature on microstructure and mechanical properties of Ti14 alloy , 2009 .

[13]  Y. Zhao,et al.  Compressive deformation and forging behavior of Ti14 alloy in semi-solid state , 2009 .

[14]  M. Z. Omar,et al.  Solid–liquid structural break-up in M2 tool steel for semi-solid metal processing , 2009, Journal of Materials Science.

[15]  Srikumar Banerjee,et al.  Phase transformations : examples from titanium and zirconium alloys , 2007 .

[16]  R. Schmid-Fetzer,et al.  Thermodynamic calculation as a tool for thixoforming alloy and process development , 2006 .

[17]  H. Chang,et al.  Research on microstructure and mechanical properties of a new α + Ti2Cu alloy after semi-solid deformation , 2006 .

[18]  M. Ramadan,et al.  Flow analysis of semi solid processing for grey cast iron , 2005 .

[19]  H. Atkinson,et al.  Thermodynamic Prediction of Thixoformability in Alloys Based on the Al-Si-Cu and Al-Si-Cu-Mg Systems , 2005 .

[20]  R. Ghomashchi,et al.  SEMI-SOLID METAL PROCESSING ROUTES: AN OVERVIEW , 2005 .

[21]  H. Chang,et al.  Semi-solid oxidation and deformation behavior of Ti14 alloy , 2004 .

[22]  Q. Han,et al.  The use of thermodynamic simulation for the selection of hypoeutectic aluminum-silicon alloys for semi-solid metal processing , 2004 .

[23]  Y. Liu,et al.  Thermodynamic predictions of Mg - Al - M (M=Zn, Mn, Si) alloy compositions amenable to semisolid metal processing , 2004 .

[24]  Suyitno,et al.  Mechanical properties in the semi-solid state and hot tearing of aluminium alloys , 2004 .

[25]  H. Atkinson,et al.  Thermodynamic predictions of wrought alloy compositions amenable to semi-solid processing , 2003 .

[26]  H. Okamoto.  Cu-Ti (Copper-Titanium) , 2002 .

[27]  E. J. Zoqui,et al.  Contribution to the study of mechanisms involved in the formation of rheocast structure , 2001 .

[28]  P. J. Ward,et al.  Near net shaping by semi-solid metal processing , 2000 .

[29]  P. Wollants,et al.  Thermodynamic Optimisation of the Cu-Ti System , 1996 .

[30]  Merton C. Flemings,et al.  Behavior of metal alloys in the semisolid state , 1991 .

[31]  E. Schulson.  Electron channelling patterns in scanning electron microscopy , 1977 .