Maintenance actions planning in industrial centrifugal compressor based on failure analysis

The industrial maintenance implementation requires to the behaviour system analysis and their components. In this work, we optimize the maintenance actions to eliminate failures in the inspected industrial process. Our purpose in this work is to improve the components reliability in gas compression system, by the planning of the maintenance actions based on failure analysis using the intervention optimization in industrial centrifugal compressor plant. The finality of this proposed approach is proved by the improvement of the reliability performances and by the availability of this oil installation.

[1]  Siegfried Eisinger,et al.  Modeling of uncertainties in reliability centered maintenance - a probabilistic approach , 2001, Reliab. Eng. Syst. Saf..

[2]  Boris Kalitventzeff,et al.  Dynamic simulation and control of gas turbines and compressor systems , 1993 .

[3]  Stephen Ogaji,et al.  Rotor-blades' profile influence on a gas-turbine's compressor effectiveness , 2008 .

[4]  Margot P. C. Weijnen,et al.  Integrated optimal reliable design, production, and maintenance planning for multipurpose process plants , 2003, Comput. Chem. Eng..

[5]  J. L. Otegui,et al.  Failure analysis of packing plate in a hyper compressor at a petrochemical plant , 2008 .

[6]  Andrew Ball,et al.  Numerical simulation and experimental study of a two-stage reciprocating compressor for condition monitoring , 2008 .

[7]  Y. Huang,et al.  A measurement method for air pressures in compressor vane segments , 2008 .

[8]  Sandip Roy,et al.  Maintenance optimization using probabilistic cost-benefit analysis , 2009 .

[9]  Alaa Chateauneuf,et al.  Opportunistic policy for optimal preventive maintenance of a multi-component system in continuous operating units , 2009, Comput. Chem. Eng..

[10]  María Del Carmen Carnero Moya,et al.  Selection of diagnostic techniques and instrumentation in a predictive maintenance program. A case study , 2005, Decis. Support Syst..

[11]  Yi-Guang Li,et al.  Gas turbine performance prognostic for condition-based maintenance , 2009 .

[12]  Anthony Kelly,et al.  Maintenance and the industrial organization , 2006 .

[13]  Lazaros G. Papageorgiou,et al.  Planning and Maintenance Optimization for Multipurpose Plants , 2000 .

[14]  Djamil Aïssani,et al.  Impact of few failure data on the opportunistic replacement policy for multi-component systems , 2010, Reliab. Eng. Syst. Saf..

[15]  Enrique F. Castillo,et al.  Sensitivity analysis in optimization and reliability problems , 2008, Reliab. Eng. Syst. Saf..

[16]  Gholam Hossein Farrahi,et al.  Failure analysis of a gas turbine compressor , 2011 .

[17]  P. G. Fazzini,et al.  Cause and effect assessment after a complex failure of a large ethylene compressor , 2006 .

[18]  Chanan Singh,et al.  The effect of transformer maintenance parameters on reliability and cost: a probabilistic model , 2004 .

[19]  Jean-Christophe Lapayre,et al.  A new industrial cooperative tele-maintenance platform , 2004, Comput. Ind. Eng..

[20]  Song Jian,et al.  Failure analysis and optimization design of a centrifuge rotor , 2007 .

[21]  W. J. Moore,et al.  An intelligent maintenance system for continuous cost-based prioritisation of maintenance activities , 2006, Comput. Ind..

[22]  Jun Hu,et al.  Fault Diagnosis System of Rotating Machinery Vibration Signal , 2011 .

[23]  Weifeng Hou,et al.  Simulation based approach for optimal scheduling of fuel gas system in refinery , 2010 .

[24]  Zouakia Rochdi,et al.  Industrial systems maintenance modelling using Petri nets , 1999 .

[25]  El Houssaine Aghezzaf,et al.  An integrated production and preventive maintenance planning model , 2007, Eur. J. Oper. Res..