Incorporating small fatigue crack growth in probabilistic life prediction: Effect of stress ratio in Ti–6Al–2Sn–4Zr–6Mo

Abstract The effect of stress ratio on the statistical aspects of small fatigue crack growth behavior was studied in a duplex microstructure of Ti–6Al–2Sn–4Zr–6Mo (Ti-6-2-4-6) at 260 °C with particular emphasis on incorporating small-crack data into probabilistic life prediction and the influence of stress ratio on probabilistic lifetime limits. A Focused Ion Beam (FIB) was used to machine micro-notches in test specimens, which served as crack-initiation sites and enabled the acquisition of multiple small-crack growth data sets from single experiment. Stress ratios of −0.5, 0.05, and 0.5 were employed, and small-crack growth was monitored by the acetate replication method. Qualitatively, change in the stress ratio produced almost negligible influence on the small-crack growth behavior when plotted as crack growth rate (d a /d N ) vs. applied stress intensity factor range (Δ K ). A probabilistic method was employed to represent the variability in the small-crack growth behavior and the statistical differences with respect to stress ratio where a method of optimization of the small-crack growth model parameters, based on a minimization of the error between the predicted and the measured crack length vs. cycles ( a vs. N ) data, was used. In spite of qualitative similarity, differences in the statistical parameters of small-crack growth as a function of stress ratio were found to be significant in life prediction. The methods for representation and probabilistic treatment of small-crack data were also shown to be important factors in incorporation of the small-crack regime in probabilistic life prediction.

[1]  Robert O. Ritchie,et al.  Fatigue crack propagation thresholds for long and short cracks in René 95 Nickel-base superalloy , 1982 .

[2]  John Goodman,et al.  Mechanics applied to engineering , 1904 .

[3]  K. S. Ravichandran,et al.  Effect of mean stress (stress ratio) and aging on fatigue-crack growth in a metastable beta titanium alloy, Ti-10V-2Fe-3Al , 2000 .

[4]  T. Nicholas,et al.  On the use of the Goodman diagram for high cycle fatigue design , 1996 .

[5]  N. Dowling,et al.  Mean stress effects in stress-life fatigue and the Walker equation , 2009 .

[6]  J. M. Larsen,et al.  Towards a physics-based description of fatigue variability behavior in probabilistic life-prediction , 2009 .

[7]  D. Ruppert,et al.  Transformation and Weighting in Regression , 1988 .

[8]  Brad L. Boyce,et al.  Effect of load ratio and maximum stress intensity on the fatigue threshold in Ti–6Al–4V , 2001 .

[9]  C. Beevers.  Fatigue crack growth characteristics at low stress intensities of metals and alloys , 1977 .

[10]  R. C. McClung,et al.  A literature survey on the stability and significance of residual stresses during fatigue , 2007 .

[11]  K. Sadananda,et al.  A REVIEW OF CRACK CLOSURE, FATIGUE CRACK THRESHOLD AND RELATED PHENOMENA , 1994 .

[12]  Robert O. Ritchie,et al.  Small fatigue cracks: A statement of the problem and potential solutions , 1986 .

[13]  Yibin Xue,et al.  Modeling fatigue small-crack growth with confidence - A multistage approach , 2010 .

[14]  J. Allison,et al.  Small-Crack Test Methods , 1992 .

[15]  Welch Bl.  THE GENERALIZATION OF ‘STUDENT'S’ PROBLEM WHEN SEVERAL DIFFERENT POPULATION VARLANCES ARE INVOLVED , 1947 .

[16]  K. Miller.  THE SHORT CRACK PROBLEM , 1982 .

[17]  Phil E. Irving,et al.  The role of residual stress and heat affected zone properties on fatigue crack propagation in friction stir welded 2024-T351 aluminium joints , 2003 .

[18]  Theo Fett,et al.  A toughness test device with opposite roller loading , 2001 .

[19]  S. Stanzl-Tschegg,et al.  Demonstration of an endurance limit in cast 319 aluminum , 2003 .

[20]  Yoshiharu Mutoh,et al.  THE EFFECT OF RESIDUAL STRESSES INDUCED BY SHOT‐PEENING ON FATIGUE CRACK PROPAGATION IN TWO HIGH STRENGTH ALUMINIUM ALLOYS , 1987 .

[21]  H. R. Millwater,et al.  Probabilistic sensitivity analysis in life-prediction of an α + β titanium alloy , 2009 .

[22]  P. C. Paris,et al.  A Critical Analysis of Crack Propagation Laws , 1963 .

[23]  C Annis,et al.  Probabilistic Life Prediction Isn't as Easy as It Looks , 2004 .

[24]  J. Lankford.  THE INFLUENCE OF MICROSTRUCTURE ON THE GROWTH OF SMALL FATIGUE CRACKS , 1985 .

[25]  David L. Davidson,et al.  The influence of crack tip plasticity in the growth of small fatigue cracks , 1984 .

[26]  J. M. Larsen,et al.  Nominal vs Local Shot-Peening Effects on Fatigue Lifetime in Ti-6Al-2Sn-4Zr-6Mo at Elevated Temperature , 2009 .

[27]  R. Ritchie,et al.  Propagation of short fatigue cracks , 1984 .

[28]  S. Jha,et al.  Small fatigue crack growth and failure mode transitions in a Ni-base superalloy at elevated temperature , 2010 .

[29]  K. Sadananda,et al.  Residual stress effects on near-threshold fatigue crack growth in friction stir welds in aerospace alloys , 2003 .

[30]  Charles Annis,et al.  An assessment of the role of near-threshold crack growth in high-cycle-fatigue life prediction of aerospace titanium alloys under turbine engine spectra , 1996 .

[31]  Ritchie,et al.  CRACK CLOSURE AND THE FATIGUE-CRACK PROPAGATION THRESHOLD AS A FUNCTION OF LOAD RATIO , 2002 .

[32]  J. F. Knott,et al.  Mechanisms of fatigue crack growth in low alloy steel , 1973 .

[33]  Anthony W. Thompson,et al.  Roughness-Induced Crack Closure: An Explanation for Microstructurally Sensitive Fatigue Crack Growth , 1983 .

[34]  Daniel Kujawski,et al.  A fatigue crack driving force parameter with load ratio effects , 2001 .

[35]  Brad L. Boyce,et al.  Thresholds for high-cycle fatigue in a turbine engine Ti–6Al–4V alloy , 1999 .

[36]  B. A. Cowles,et al.  High cycle fatigue in aircraft gas turbines—an industry perspective , 1996 .

[37]  David L. McDowell,et al.  Frequency and stress ratio effects in high cycle fatigue of Ti-6Al-4V , 1999 .

[38]  Reji John,et al.  Stress Ratio Effects on Small Fatigue Crack Growth in Ti-6Al-4V (Preprint) , 2008 .

[39]  K. Pearson.  Biometrika , 1902, The American Naturalist.

[40]  David Taylor,et al.  FATIGUE CRACK PROPAGATION BEHAVIOUR OF SHORT CRACKS; THE EFFECT OF MICROSTRUCTURE , 1981 .

[41]  J. Newman,et al.  Fatigue-life prediction methodology using small-crack theory , 1999 .

[42]  R. Boyer,et al.  Fatigue behavior of titanium alloys , 1999 .

[43]  Subra Suresh,et al.  ON THE INFLUENCE OF ENVIRONMENT ON THE LOAD RATIO DEPENDENCE OF FATIGUE THRESHOLDS IN PRESSURE VESSEL STEEL , 1983 .

[44]  W. Soboyejo,et al.  An investigation of the effects of stress ratio and crack closure on the micromechanisms of fatigue crack growth in Ti-6Al-4V , 1997 .

[45]  J. M. Larsen,et al.  A new paradigm of fatigue variability behavior and implications for life prediction , 2007 .

[46]  S. J. Hudak,et al.  Small Crack Behavior and the Prediction of Fatigue Life , 1981 .