Nozzle and needle during high viscosity adhesive jetting based on piezoelectric jet dispensing

A piezoelectric impinging jet valve is used as a study object to investigate the effect of the ball needle in the existing impinging jet and nozzle structure of the valve on the performance of the jet. First, FLUENT software is used under different ball needle and nozzle structural parameters to simulate the pressure distribution that the ball needle and nozzle in the pressure cavity form when the ball needle hits the nozzle, by arranging the structure model of the ball needle and impact valve nozzle. The piezoelectric impact injection valve and the experiment test system are then designed. Test results show that the ball needle and nozzle structural parameters are closely related to the injection performance of the impact valve. Under certain conditions, a greater needle radius corresponds to a smaller nozzle aperture and taper. Moreover, high-viscosity liquid jetting is easily achieved. By using a ball needle with a radius of 1.5 mm, a taper angle of 60°, and a nozzle diameter of 0.1 mm, we can realize the industrial viscosity of 58 000 cps in glue spray, and the injection plastic fluid volume is 0.62 μl.

[1]  Xiaohui Du,et al.  Simulation and experiment study on adhesive ejection behavior in jetting dispenser , 2014 .

[2]  Y. Ham,et al.  Piezoelectrically Driven Dispensing Head for Encapsulation of Light Emitting Diode Chip , 2012 .

[3]  Jianhua Zhang,et al.  A fluid dynamic analysis in the chamber and nozzle for a jetting dispenser design , 2010, 2010 11th International Conference on Electronic Packaging Technology & High Density Packaging.

[4]  Junfeng Xiao,et al.  Experimental study on high viscosity fluid micro-droplet jetting system , 2010 .

[5]  Jianhua Zhang,et al.  A jetting system for chip on glass package , 2009, 2009 International Conference on Electronic Packaging Technology & High Density Packaging.

[6]  Guiling Deng,et al.  Simulation and experimental study on temperature field of fluid jet-dispenser , 2009, 2009 International Conference on Electronic Packaging Technology & High Density Packaging.

[7]  Seung-bok Choi,et al.  The design and control of a jetting dispenser for semiconductor electronic packaging driven by a piezostack and a flexible beam , 2008 .

[8]  Deng Guiling,et al.  The influence of structural parameters of electromagnetic fluid jetting dispenser , 2008, 2008 International Conference on Electronic Packaging Technology & High Density Packaging.

[9]  Seung-Bok Choi,et al.  Design of a new mechanism for jetting dispenser featuring piezoactuator , 2008 .

[10]  Seung-Bok Choi,et al.  Design of a Novel Jetting Dispenser Featuring Piezostack and Linear Pump , 2008 .

[11]  Seung-Bok Choi,et al.  A new type of piezostack-driven jetting dispenser for semiconductor electronic packaging: modeling and control , 2008 .

[12]  Deng Guiling,et al.  The Influence of Fluid Viscosity of Fluid Jetting Dispensing , 2007, 2007 International Symposium on High Density packaging and Microsystem Integration.

[13]  R. Zengerle,et al.  Non-Contact Nanoliter & Picoliter Liquid Dispensing , 2007, TRANSDUCERS 2007 - 2007 International Solid-State Sensors, Actuators and Microsystems Conference.

[14]  Li Jianping,et al.  Technology development and basic theory study of fluid dispensing - a review , 2004, Proceedings of the Sixth IEEE CPMT Conference on High Density Microsystem Design and Packaging and Component Failure Analysis (HDP '04).

[15]  Xiaohui Du,et al.  Design and Experiment of a Jetting Dispenser Driven by Piezostack Actuator , 2013, IEEE Transactions on Components, Packaging and Manufacturing Technology.