FINITE ELEMENT-BASED FATIGUE BEHAVIOUR OF SPRINGS IN AUTOMOBILE SUSPENSION

This paper presents the fatigue behaviour of springs used in shock absorbers in automobile suspension systems. SAE 9254 is considered as a spring material. Triangular waves with a frequency of 4 Hz and SAE standard suspension loading history (SAESUS) were used for fatigue analysis. Both load histories are scaled according to the maximum and minimum values of deflection, as spring height at full-bump and full-rebound, respectively. Finite element analysis was carried out using the linear static approach. Fatigue analysis was performed using the strain-life method. Absolute maximum principal and critical plane approaches gave results of reasonable accuracy, but later had a considerably longer solution time, while signed von Mises and signed shear approaches gave very conservative results. Thus the absolute maximum principal method is found to be the best suited. The results show that the spring did not fail before 4×10 5 cycles at 4 Hz for wave time history and 70,000 repeats for SAESUS time history at critical location.

[1]  M. RahmanM.,et al.  Finite element based vibration fatigue analysis of a new two-stroke linear generator engine component , 2007 .

[2]  K. Kadirgama,et al.  Fatigue Life Prediction of Lower Suspension Arm Using Strain-Life Approach , 2009 .

[3]  M. SaniM.S.,et al.  Application of Multibody Simulation for Fatigue Life Estimation , 2013 .

[4]  R. A. Bakar,et al.  Notice of RetractionRobust design of suspension arm based on stochastic design improvement , 2010, 2010 2nd International Conference on Mechanical and Electronics Engineering.

[5]  Karl Popp,et al.  Ground Vehicle Dynamics , 2010 .

[6]  H. O. Fuchs,et al.  Metal fatigue in engineering , 2001 .

[7]  M. RahmanM.,et al.  Multiaxial fatigue behavior of cylinder head for a free piston linear engine , 2009 .

[8]  M. Matsuichi,et al.  Fatigue of metals subjected to varying stress , 1968 .

[9]  Ali Fatemi,et al.  Torsional deformation and fatigue of hardened steel including mean stress and stress gradient effects , 2004 .

[10]  Sigmund K. Ås.  Fatigue Life Prediction of an Aluminium Alloy Automotive Component Using Finite Element Analysis of Surface Topography , 2006 .

[11]  Md. Abdul Maleque,et al.  Finite Element Based Fatigue Life Prediction of Cylinder Head for Two-Stroke Linear Engine Using Stress-Life Approach , 2008 .

[12]  Salha Abdullah,et al.  Effect of Nitriding Treatment on Fatigue life for Free Piston Linear Engine Component using Frequency Response Method: a Finite Element Approach , 2007 .

[13]  R. Brook,et al.  Cumulative Damage in Fatigue: A Step towards Its Understanding , 1969 .

[14]  Salha Abdullah,et al.  Finite Element Based Durability Assessment of a Free Piston Linear Engine Component , 2007 .

[15]  Gérard Mesmacque,et al.  Multiaxial fatigue and failure analysis of helical compression springs , 2006 .

[16]  M. RahmanM.,et al.  Fatigue Life Prediction of Lower Suspension Arm UsingStrain-Life Approach , 2009 .

[17]  Mehmet Firat,et al.  Analytical durability modeling and evaluation¿complementary techniques for physical testing of automotive components , 2004 .

[18]  M. SaniM.S.,et al.  Fatigue Life Prediction of Spot-Welded Structures: A Finite Element Analysis Approach , 2008 .

[19]  M. M. Noor,et al.  Fatigue Life Prediction of Spot-Welded Structures : A Finite Element Analysis Approach , 2008 .

[20]  Shahrum Abdullah,et al.  Comparison Between Experimental Road Data and Finite Element Analysis Data for the Automotive Lower Suspension Arm , 2009 .

[21]  Siti Norul Huda Sheikh Abdullah,et al.  Finite Element Based Fatigue Life Prediction of a New Free Piston Engine Mounting , 2008 .