Impression creep testing and microstructurally adaptive creep modeling of lead free solder interconnects

Creep plays an important role in the reliability of solder joints under thermo-mechanical fatigue conditions encountered by a microelectronic package during service. In addition, the fine intermetallic precipitates (Ag/sub 3/Sn and/or Cu/sub 6/Sn/sub 5/) in the microstructures of the new lead-free solders (Sn-Ag and Sn-Ag-Cu) can undergo significant in situ strain-enhanced coarsening during TMC, resulting in in-service evolution of the creep behavior of the joints. Since there are significant microstructural/compositional differences between bulk solder samples and tiny microelectronic solder joints, it is critical to develop accurate creep testing methodologies on tiny life-sized solder joints and microstructurally adaptive constitutive creep models for the emerging Pb-free solder alloys. In this paper, we present creep data obtained from tests conducted on individual Sn/sub 4/Ag/sub 0.5/Cu ball grid array (BGA) solder balls attached to a packaging substrate, using a newly developed miniaturized impression creep apparatus, which affords high test throughput with minimal sample preparation. Coarsening of intermetallic particles is demonstrated to influence creep behavior in two ways. At low stresses, the creep rate increases proportionately with precipitate size. At high stresses, precipitate coarsening influences creep response by altering the threshold stress for particle-limited creep. Based on the experimental observations, a microstructurally adaptive creep model, which accounts for the effects of coarsening on the creep response of solder joints, and is capable of adjusting itself as solder joint microstructures evolve during service, is presented, along with experimental determination of the relevant coarsening kinetics parameters.

[1]  Bahgat Sammakia,et al.  Journal of Electronic Packaging, Transactions of the ASME: Foreword , 2004 .

[2]  I. Dutta,et al.  Impression creep characterization of rapidly cooled Sn–3.5Ag solders , 2004 .

[3]  J. Li,et al.  Impression creep and other localized tests , 2002 .

[4]  R. Cahn,et al.  Materials science and engineering , 2023, Nature.

[5]  Oleg N. Senkov,et al.  Grain growth in a superplastic Zn-22% Al alloy , 1986 .

[6]  E. Arzt,et al.  The kinetics of dislocation climb over hard particles—II. Effects of an attractive particle-dislocation interaction , 1988 .

[7]  M. A Clark,et al.  Deformation enhanced grain growth in a superplastic Sn-1% Bi alloy , 1973 .

[8]  I. Lifshitz,et al.  The kinetics of precipitation from supersaturated solid solutions , 1961 .

[9]  C. Marshall,et al.  Underfill constraint effects during thermomechanical cycling of flip-chip solder joints , 2002 .

[10]  R. Mahajan,et al.  Miniaturized impression creep testing of ball grid array solder balls attached to microelectronic packaging substrates , 2004 .

[11]  Peter Hacke,et al.  Computer Simulation of Thermo-Mechanical Fatigue of Solder Joints Including Microstructure Coarsening , 1993 .

[12]  F. Vnuk,et al.  The solid solubility of silver, gold and zinc in metallic tin , 1981 .

[13]  I. Dutta.  A constitutive model for creep of lead-free solders undergoing strain-enhanced microstructural coarsening: A first report , 2003 .

[14]  Di Yang,et al.  Influence of microstructure size on the plastic deformation kinetics, fatigue crack growth rate, and low-cycle fatigue of solder joints , 1999 .

[15]  Robert W. Messler,et al.  Microstructure evolution of eutectic Sn-Ag solder joints , 1994 .