Optical Tip Clearance Measurements as a Tool for Rotating Disk Characterization

An experimental investigation on the vibrational behavior of a rotating disk by means of three optical fiber sensors is presented. The disk, which is a scale model of the real disk of an aircraft engine, was assembled in a wind tunnel in order to simulate real operation conditions. The pressure difference between the upstream and downstream sides of the disk causes an airflow that might force the disk to vibrate. To characterize this vibration, a set of parameters was determined by measuring the tip clearance of the disk: the amplitude, the frequency and the number of nodal diameters in the disk. All this information allowed the design of an upgraded prototype of the disk, whose performance was also characterized by the same method. An optical system was employed for the measurements, in combination with a strain gauge mounted on the disk surface, which served to confirm the results obtained. The data of the strain gauge coincided closely with those provided by the optical fiber sensors, thus demonstrating the suitability of this innovative technique to evaluate the vibrational behavior of rotating disks.

[1]  K F Heermann,et al.  STUDY TO IMPROVE TURBINE ENGINE ROTOR BLADE CONTAINMENT , 1977 .

[2]  Zhang Yong-kui,et al.  Tip clearance optical measurement for rotating blades , 2011, MSIE 2011.

[3]  Albert Langkamp,et al.  In-process, non-destructive, dynamic testing of high-speed polymer composite rotors , 2015 .

[4]  Gotzon Aldabaldetreku,et al.  An Optical Fiber Bundle Sensor for Tip Clearance and Tip Timing Measurements in a Turbine Rig , 2013, Sensors.

[5]  Joseba Zubia,et al.  Different Configurations of a Reflective Intensity-Modulated Optical Sensor to Avoid Modal Noise in Tip-Clearance Measurements , 2015, Journal of Lightwave Technology.

[6]  Gotzon Aldabaldetreku,et al.  Optical Fiber Sensors for Aircraft Structural Health Monitoring , 2015, Sensors.

[7]  Gotzon Aldabaldetreku,et al.  Optical tip clearance measurements for rotating disk characterization , 2015, 2015 17th International Conference on Transparent Optical Networks (ICTON).

[8]  Xikun Wang,et al.  An experimental study on feedback control of rotating disk flutter , 2005 .

[9]  L M Sim,et al.  Damage detection and assessment in fibre-reinforced composite structures with embedded fibre optic sensors-review , 2002 .

[10]  Paolo Castellini,et al.  Development of the tracking laser vibrometer: Performance and uncertainty analysis , 2000 .

[11]  J.J.Iturregui,et al.  A New Transonic Test Turbine Facility , 2003 .

[12]  Mark R. Woike,et al.  Investigation of a cross-correlation based optical strain measurement technique for detecting radial growth on a rotating disk , 2013, Smart Structures.

[13]  A. Güemes,et al.  SHM Technologies and Applications in Aircraft Structures , 2013 .

[14]  Hooman Nabovati,et al.  Fiber Optic Sensors , 2008 .

[15]  Josu Amorebieta,et al.  Tip-Clearance Measurement in the First Stage of the Compressor of an Aircraft Engine , 2016, Sensors.

[16]  Joseba Zubia,et al.  Evaluation of the vibrational behaviour of a rotating disk by optical tip-clearance measurements , 2015, Optical Metrology.

[17]  Ten-Huei Guo,et al.  An investigation of life extending control techniques for gas turbine engines , 2001, Proceedings of the 2001 American Control Conference. (Cat. No.01CH37148).

[18]  Marianna A. Shubov,et al.  Flutter Phenomenon in Aeroelasticity and Its Mathematical Analysis , 2006 .

[19]  Christophe Pierre,et al.  Experimental Investigation of Mode Localization and Forced Response Amplitude Magnification for a Mistuned Bladed Disk , 2000 .

[20]  Richard E. Martin,et al.  Vibration Based Crack Detection in a Rotating Disk , 2003 .

[21]  Gotzon Aldabaldetreku,et al.  Turbine-blade tip clearance and tip timing measurements using an optical fiber bundle sensor , 2013, Optical Metrology.