Theoretical modeling of thermoelectric generator with particular emphasis on the effect of side surface heat transfer

Based on one-dimensional steady analysis, a comprehensive theoretical model for analyzing the performance of TEGs (thermoelectric generators) is proposed, in which finite element method and integral-averaged Seebeck coefficient are employed to effectively consider the effects of temperature-dependence of thermoelectric materials and Thomson effect respectively. The optimal segments for each case are identified. Under the optimal segments, the impact of SSHT (side surface heat transfer) is particularly emphasized for two commercial thermoelectric materials. Compared with that without considering SSHT, the present model has the similar form, but an additional term is included and the potential fractions of Fourier heat conduction and Joule heat are reduced. Also the nonlinear temperature distributions along the legs are presented, and the variation of the efficiency with leg length under CTMV (constant thermoelectric material volume) is changed from monotonously increasing to downward parabola. As the SSHT coefficient h increases, the efficiency decreases. However, the maximum output power emerges depending on h and thermoelectric materials, indicating that proper h is beneficial for cost-free heat sources. Considering that h may vary at any time, TEGs with leg length between 2 mm and 4 mm under CTMV of 22.5 mm3 is recommended.

[1]  M. Rivaletto,et al.  Study of a TE (thermoelectric) generator incorporated in a multifunction wood stove , 2011 .

[2]  Christophe Goupil,et al.  Comparison of different modeling approaches for thermoelectric elements , 2013 .

[3]  P. Ziolkowski,et al.  Estimation of Thermoelectric Generator Performance by Finite Element Modeling , 2010 .

[4]  Ronnie Andersson,et al.  Analysis of Thermoelectric Generator Performance by Use of Simulations and Experiments , 2014, Journal of Electronic Materials.

[5]  Anke Weidenkaff,et al.  A solar cavity-receiver packed with an array of thermoelectric converter modules , 2011 .

[6]  Bekir Sami Yilbas,et al.  Thermodynamic analysis of a thermoelectric power generator in relation to geometric configuration device pins , 2014 .

[7]  L. Rosendahl,et al.  A three-dimensional numerical model of thermoelectric generators in fluid power systems , 2011 .

[8]  Matthew M. Barry,et al.  Thermoelectric Performance of Novel Composite and Integrated Devices Applied to Waste Heat Recovery , 2013 .

[9]  D. Astrain,et al.  Dynamic model for simulation of thermoelectric self cooling applications , 2013 .

[10]  Jing Liu,et al.  Liquid metal based thermoelectric generation system for waste heat recovery , 2011 .

[11]  Kenneth McEnaney,et al.  Modeling of concentrating solar thermoelectric generators , 2011 .

[12]  Shahryar Rahnamayan,et al.  Multi-objective thermal analysis of a thermoelectric device: Influence of geometric features on device characteristics , 2014 .

[13]  Matteo Chiesa,et al.  Modeling and optimization of solar thermoelectric generators for terrestrial applications , 2012 .

[14]  Xiong Yu,et al.  A holistic 3D finite element simulation model for thermoelectric power generator element , 2014 .

[15]  Gequn Shu,et al.  Investigation and design optimization of exhaust-based thermoelectric generator system for internal combustion engine , 2014 .

[16]  Srinath V. Ekkad,et al.  Simulation of thermoelectric-hydraulic performance of a thermoelectric power generator with longitudinal vortex generators , 2015 .

[17]  Gang Chen,et al.  Theoretical efficiency of solar thermoelectric energy generators , 2011 .

[18]  Sun Feng-rui,et al.  A numerical model and comparative investigation of a thermoelectric generator with multi-irreversibi , 2011 .

[19]  Peng Li,et al.  Design of a Concentration Solar Thermoelectric Generator , 2010 .

[20]  Zijun Yan,et al.  The influence of Thomson effect on the maximum power output and maximum efficiency of a thermoelectric generator , 1996 .

[21]  Shuang-Ying Wu,et al.  Theoretical analysis on the performance of annular thermoelectric couple , 2015 .

[22]  R. Bjork,et al.  Analysis of the internal heat losses in a thermoelectric generator , 2014, 1409.6743.

[23]  Xing Zhang,et al.  Optimization design method of thermoelectric generator based on exhaust gas parameters for recovery of engine waste heat , 2015 .

[24]  M. Oh,et al.  Estimation of Power Generation from Thermoelectric Devices: Model Analysis and Performance Measurements , 2010 .

[25]  Sheng-Chung Tzeng,et al.  Parametric study of heat-transfer design on the thermoelectric generator system , 2014 .

[26]  Jiawei Yao,et al.  Effects of temperature non-uniformity over the heat spreader on the outputs of thermoelectric power generation system , 2013 .

[27]  Keith A. Woodbury,et al.  Modeling and Analysis of a Combined Photovoltaic-Thermoelectric Power Generation System , 2012 .

[28]  Lasse Rosendahl,et al.  Experimental Study of a Thermoelectric Generation System , 2011 .

[29]  Minking K. Chyu,et al.  Mathematical modeling and numerical characterization of composite thermoelectric devices , 2013 .

[30]  Lingen Chen,et al.  Modeling and performance analysis of a two-stage thermoelectric energy harvesting system from blast furnace slag water waste heat , 2014 .

[31]  Xiaolong Gou,et al.  Modeling, experimental study and optimization on low-temperature waste heat thermoelectric generator system , 2010 .

[32]  Emil Sandoz-Rosado,et al.  On the Thomson effect in thermoelectric power devices , 2013 .

[33]  G. J. Snyder,et al.  Complex thermoelectric materials. , 2008, Nature materials.

[34]  Shohel Mahmud,et al.  Numerical simulation of nanostructured thermoelectric generator considering surface to surrounding convection , 2014 .

[35]  S. W. Angrist.  Direct energy conversion , 1976 .

[36]  Jianlin Yu,et al.  Experimental study on low-temperature waste heat thermoelectric generator , 2009 .

[37]  Mei-Jiau Huang,et al.  A simulation study of automotive waste heat recovery using a thermoelectric power generator , 2013 .

[38]  Aldo Steinfeld,et al.  A 1kWe thermoelectric stack for geothermal power generation – Modeling and geometrical optimization , 2012 .

[39]  Chang Chung Yang,et al.  Modeling and simulation for the design of thermal-concentrated solar thermoelectric generator , 2014 .

[40]  Christophe Goupil,et al.  Study of a thermoelement’s behaviour through a modelling based on electrical analogy , 2010 .

[41]  Lingen Chen,et al.  Thermoelectric power generation driven by blast furnace slag flushing water , 2014 .

[42]  Wei-Hsin Chen,et al.  Experimental study on thermoelectric modules for power generation at various operating conditions , 2012 .

[43]  Gang Chen,et al.  High-performance flat-panel solar thermoelectric generators with high thermal concentration. , 2011, Nature materials.

[44]  Jincan Chen,et al.  Evaluation of temperature-dependent thermoelectric performances based on PbTe1−yIy and PbTe: Na/Ag2Te materials , 2014 .

[45]  K. Mossi,et al.  Effect of various leg geometries on thermo-mechanical and power generation performance of thermoelectric devices , 2014 .

[46]  K. Romanjek,et al.  High temperature solar thermoelectric generator – Indoor characterization method and modeling , 2015 .

[47]  Bekir Sami Yilbas,et al.  The thermoelement as thermoelectric power generator: Effect of leg geometry on the efficiency and power generation , 2013 .

[48]  Min Chen,et al.  Theoretical, experimental and numerical diagnose of critical power point of thermoelectric generators , 2014 .

[49]  Wei-Chin Chang,et al.  A mathematic model of thermoelectric module with applications on waste heat recovery from automobile engine , 2010 .

[50]  Luca Francioso,et al.  Experimental assessment of thermoelectric generator package properties: Simulated results validation and real gradient capabilities , 2015 .

[51]  Jing-Hui Meng,et al.  Characteristics analysis and parametric study of a thermoelectric generator by considering variable material properties and heat losses , 2015 .

[52]  Brandon Ohara,et al.  Exergetic analysis of a solar thermoelectric generator , 2015 .

[53]  Li Shi,et al.  High fidelity finite difference model for exploring multi-parameter thermoelectric generator design space , 2014 .

[54]  L. Bell.  Cooling, Heating, Generating Power, and Recovering Waste Heat with Thermoelectric Systems , 2008, Science.

[55]  A. Bauknecht,et al.  Analysis of Annular Thermoelectric Couples with Nonuniform Temperature Distribution by Means of 3-D Multiphysics Simulation , 2013, Journal of Electronic Materials.

[56]  Bin Wu,et al.  Thermoelectric topping cycles for power plants to eliminate cooling water consumption , 2014 .

[57]  Bekir Sami Yilbas,et al.  Thermoelectric device and optimum external load parameter and slenderness ratio , 2010 .

[58]  Shixue Wang,et al.  Theoretical analysis of a thermoelectric generator using exhaust gas of vehicles as heat source , 2013 .

[59]  Emil Sandoz-Rosado,et al.  Experimental Characterization of Thermoelectric Modules and Comparison with Theoretical Models for Power Generation , 2009 .

[60]  R. Buist,et al.  Calculation of thermoelectric power generation performance using finite element analysis , 1997, XVI ICT '97. Proceedings ICT'97. 16th International Conference on Thermoelectrics (Cat. No.97TH8291).

[61]  Xiaolong Gou,et al.  Detailed Modeling and Irreversible Transfer Process Analysis of a Multi-Element Thermoelectric Generator System , 2011 .

[62]  Peng Li,et al.  Thermal design and management for performance optimization of solar thermoelectric generator , 2012 .