Research on impacts of mechanical vibrations on the production machine to its rate of change of technical state

The article observes the amount of vibration on the bearing house of a turning lathe selected in advance through the change of the revolutions per minute and the thickness of the removed material in frontal type of lathe processing. Increase in mechanical vibration values depending on the value of nominal thickness of splinter was observed during changing technological parameters of the drilling process as a consequence of rotation speed of the motor. The vibration acceleration amplitude course changes depending on the frequencies are evaluated together for 400, 800 and 1200 motor r/min. A piezoelectric sensor of the type 4507B-004 from the Brüel & Kjaer Company was used for monitoring the frequency analysis of the vibration, which was attached to the bearing house of the lathe TOS SV 18RB. The vibration signal measured during the processing and during the time period is transformed through the means of a quick Fourier transformation to the frequency spectrum in the range of 3.0–10.0 kHz. Measured values of vibration acceleration amplitude were processed and evaluated by the SignalExpress software. Graphical abstract Unwanted vibration in machine tools like lathe is one of the main problems as it affects the quality of the machined parts and tool life and creates noise during machining operation. Bearings are of paramount importance to almost all forms of rotating machinery and are the most common among machine elements. The article describes in more detail the issue of vibrations created when machining the material by lathe turning. It also includes execution, experiment evaluation in this field, and comparison of measured vibrations’ acceleration amplitude values according to the standards.

[1]  O. Cahuc,et al.  Self-Excited Vibrations in Turning: Efforts Torsor and Average Friction Coefficient Analysis , 2009, 0909.0331.

[2]  Walied A. Moussa,et al.  On the Evaluation of Dynamic Stresses in Pipelines Using Limited Vibration Measurements and FEA in the Frequency Domain , 1998 .

[3]  Régis Dufour,et al.  Nonlinear centrifugal effects on a prestressed laminated rotor , 2011 .

[4]  Jerzy T. Sawicki,et al.  Rigid Finite Element Model of a Cracked Rotor , 2012 .

[5]  Yusuf Altintas,et al.  Identification of dynamic cutting force coefficients and chatter stability with process damping , 2008 .

[6]  Slawomir Zólkiewski,et al.  Damped vibrations Problem of beams Fixed on the rotational Disk , 2011, Int. J. Bifurc. Chaos.

[7]  T. K. Kundra,et al.  Harmonics elimination algorithm for operational modal analysis using random decrement technique , 2010 .

[8]  Isabelle Guyon,et al.  An Introduction to Variable and Feature Selection , 2003, J. Mach. Learn. Res..

[9]  P. D. McFadden,et al.  A technique for calculating the time domain averages of the vibration of the individual planet gears and the sun gear in an epicyclic gearbox , 1991 .

[10]  Sunil K. Sinha,et al.  Natural frequencies of a pre-twisted blade in a centrifugal force field , 2011 .

[11]  Francisco D. Denia,et al.  Dynamics of damped rotating solids of revolution through an Eulerian modal approach , 2012 .

[12]  Z Slawomir˙.  DAMPED VIBRATIONS PROBLEM OF BEAMS FIXED ON THE ROTATIONAL DISK , 2011 .

[13]  Anton Panda,et al.  Vibration and Experimental Comparison of Machining Process , 2015 .

[14]  Marek Kočiško,et al.  Diagnostic Analysis of Cutting Tools using a Temperature Sensor , 2015 .

[15]  Mohamed Nassar,et al.  Vibration analysis of structural elements using differential quadrature method , 2012, Journal of advanced research.

[16]  S.,et al.  Dynamic flexibility of the supported-clamped beam in transportation , 2012 .

[17]  Darryll J. Pines,et al.  A review of vibration-based techniques for helicopter transmission diagnostics , 2005 .

[18]  Radoslaw Zimroz,et al.  A new feature for monitoring the condition of gearboxes in non-stationary operating conditions , 2009 .

[19]  M. Siddhpura,et al.  A review of chatter vibration research in turning , 2012 .

[21]  Radoslaw Zimroz,et al.  Gearbox Condition Estimation Using Cyclo-Stationary Properties of Vibration Signal , 2009 .

[22]  Josef Kittler,et al.  Floating search methods in feature selection , 1994, Pattern Recognit. Lett..

[23]  Ali Heidari,et al.  Optimization of cold rolling process parameters in order to increasing rolling speed limited by chatter vibrations , 2012, Journal of advanced research.