Noise reduction mechanisms of sawtooth and combed-sawtooth trailing-edge serrations

Trailing-edge serrations are add ons retrofitted to wind-turbine blades to mitigate turbulent boundary-layer trailing-edge noise. This manuscript studies the physical mechanisms behind the noise reduction by investigating the far-field noise and the hydrodynamic flow field. A conventional sawtooth and a combed-sawtooth trailing-edge serration are studied. Combed-sawtooth serrations are obtained by filling the empty space between the teeth with combs (i.e. solid filaments). Both serration geometries are retrofitted to a NACA 0018 aerofoil at zero degree angle of attack. Computations are carried out by solving the explicit, transient, compressible lattice Boltzmann equation, while the acoustic far field is obtained by means of the Ffowcs Williams and Hawkings analogy. The numerical results are validated against experiments. It is confirmed that the combed-sawtooth serrations reduce noise more than the conventional sawtooth ones for the low- and mid-frequency range. It is found that the presence of combs affects the intensity of the scattered noise but not the frequency range of noise reduction. For both configurations, the intensity of the surface pressure fluctuations decreases from the root to the tip, and noise sources are mainly located at the serrations root for the low- and mid-frequency range. The presence of the filaments generates a more uniform distribution of the noise sources along the edges with respect to the conventional serration. The installation of combs mitigates the interaction between the two sides of the aerofoil at the trailing edge and the generation of a turbulent wake in the empty space between teeth. As a result, the inward (i.e. from the serration edge to the centreline) and outward (i.e. from the serration centreline to the edge) flow motions, due to the presence of the teeth, are mitigated. It is found that the installation of serrations affects the surface pressure fluctuations integral parameters. Both the spanwise correlation length and convective velocity of the surface pressure fluctuations increase with respect to the baseline straight configuration. When both quantities are similar to the one obtained for the straight trailing edge, the effect of the slanted edge is negligible, thus corresponding to no noise reduction. It is concluded that the changes in sound radiation are mainly caused by destructive interference of the radiated sound waves for which a larger spanwise correlation length is beneficial. Finally, the difference between measurements and the literature is caused by an incorrect modelling of the spanwise correlation length, which shows a different decay rate with respect to the one obtained for a straight trailing edge.

[1]  W. V. D. Velden,et al.  Numerical and experimental investigation of a beveled trailing-edge flow field and noise emission , 2016 .

[2]  B. Launder,et al.  The numerical computation of turbulent flows , 1990 .

[3]  Jesper Madsen,et al.  Effect of trailing edge serration-flow misalignment on airfoil noise emissions , 2017 .

[4]  N. Curle.  The influence of solid boundaries upon aerodynamic sound , 1955, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[5]  P. Roache.  Perspective: A Method for Uniform Reporting of Grid Refinement Studies , 1994 .

[6]  M. Gruber,et al.  Airfoil noise reduction by edge treatments , 2012 .

[7]  Phillip Joseph,et al.  An analytical investigation of trailing edge noise reduction using novel serrations , 2013 .

[8]  Stefan Oerlemans.  Reduction of wind turbine noise using blade trailing edge devices , 2016 .

[9]  S. Orszag,et al.  Renormalization group analysis of turbulence. I. Basic theory , 1986 .

[10]  Jinhee Jeong,et al.  On the identification of a vortex , 1995, Journal of Fluid Mechanics.

[11]  G. P. Succi,et al.  A review of propeller discrete frequency noise prediction technology with emphasis on two current methods for time domain calculations , 1980 .

[12]  C. Teixeira.  INCORPORATING TURBULENCE MODELS INTO THE LATTICE-BOLTZMANN METHOD , 1998 .

[13]  P. Bhatnagar,et al.  A Model for Collision Processes in Gases. I. Small Amplitude Processes in Charged and Neutral One-Component Systems , 1954 .

[14]  G. Corcos.  The structure of the turbulent pressure field in boundary-layer flows , 1964, Journal of Fluid Mechanics.

[15]  M. S. Howe.  TRAILING EDGE NOISE AT LOW MACH NUMBERS , 1999 .

[16]  Richard D. Sandberg,et al.  Acoustic and hydrodynamic analysis of the flow around an aerofoil with trailing-edge serrations , 2012, Journal of Fluid Mechanics.

[17]  Daniele Ragni,et al.  PIV Investigation of the Flow Past Solid and Slitted Sawtooth Serrated Trailing Edges , 2016 .

[18]  Alexander van Zuijlen,et al.  Flow topology and noise emission around straight, serrated and slitted trailing edges using the Lattice Boltzmann methodology , 2016 .

[19]  Thierry Maeder,et al.  Reduction of Wind Turbine Noise using Optimized Airfoils and Trailing-Edge Serrations , 2008 .

[20]  Thierry Maeder,et al.  Reduction Of Wind Turbine Noise Using Optimized Airfoils And Trailing-Edge Serrations , 2008 .

[21]  Mirjam Snellen,et al.  Boundary layer characterization and acoustic measurements of flow-aligned trailing edge serrations , 2016 .

[22]  R. Panton,et al.  The Wavenumber-Phase Velocity Representation for the Turbulent Wall-Pressure Spectrum , 1994 .

[23]  M. Azarpeyvand,et al.  Prediction of noise from serrated trailing edges , 2015, Journal of Fluid Mechanics.

[24]  Stéphane Moreau,et al.  Extensions and limitations of analytical airfoil broadband noise models , 2010 .

[25]  Daniele Ragni,et al.  Three-dimensional flow field over a trailing-edge serration and implications on broadband noise , 2016 .

[26]  R. Parchen,et al.  Results of a wind tunnel study on the reduction of airfoil self-noise by the application of serrated blade trailing edges , 1996 .

[27]  Gianfranco Guidati,et al.  Wind Turbine Noise , 1996 .

[28]  R. Merino Martinez,et al.  Acoustic measurements of a DU96-W-180 airfoil with flow-misaligned serrations at a high Reynolds number in a closed-section wind tunnel , 2017 .

[29]  Stéphane Moreau,et al.  Direct numerical simulation of acoustic reduction using serrated trailing-edge on an isolated airfoil , 2014 .

[30]  Michael S. Howe,et al.  Aerodynamic noise of a serrated trailing edge , 1991 .

[31]  A. Iob,et al.  Numerical study of self-soise produced by an airfoil with trailing-edge serrations , 2012 .

[32]  J. Boon.  The Lattice Boltzmann Equation for Fluid Dynamics and Beyond , 2003 .

[33]  Gert Herold,et al.  A Microphone Array Method Benchmarking Exercise using Synthesized Input Data , 2017 .

[34]  Daniele Ragni,et al.  Tomographic-PIV investigation of the flow over serrated trailing-edges , 2016 .

[35]  G. Brès,et al.  Properties of the Lattice-Boltzmann Method for Acoustics , 2009 .

[36]  Sina Haeri,et al.  On the reduction of aerofoil–turbulence interaction noise associated with wavy leading edges , 2016, Journal of Fluid Mechanics.

[37]  Thomas F. Brooks,et al.  Airfoil self-noise and prediction , 1989 .

[38]  F. Fahy,et al.  Mechanics of flow-induced sound and vibration , 1989 .

[39]  Hudong Chen,et al.  Realization of Fluid Boundary Conditions via Discrete Boltzmann Dynamics , 1998 .

[40]  Leslie M. Smith,et al.  Renormalization group analysis of turbulence , 2003 .

[41]  J. Graham,et al.  Similarity rules for thin aerofoils in non-stationary subsonic flows , 1970, Journal of Fluid Mechanics.

[42]  D. Casalino.  An advanced time approach for acoustic analogy predictions , 2003 .

[43]  D. L. Hawkings,et al.  Sound generation by turbulence and surfaces in arbitrary motion , 1969, Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences.

[44]  Stefan Oerlemans,et al.  Numerical analysis of noise reduction mechanisms on improved trailing edge serrations using the Lattice Boltzmann method , 2017 .

[45]  Matthaeus,et al.  Recovery of the Navier-Stokes equations using a lattice-gas Boltzmann method. , 1992, Physical review. A, Atomic, molecular, and optical physics.

[46]  Phillip Joseph,et al.  An experimental investigation of novel trailing edge geometries on airfoil trailing edge noise reduction , 2013 .

[47]  Michael S. Howe,et al.  Noise produced by a sawtooth trailing edge , 1991 .

[48]  R. Amiet.  Noise due to turbulent flow past a trailing edge , 1976 .

[49]  P. Bruce,et al.  Coherent structures shed by multiscale cut-in trailing edge serrations on lifting wings , 2017 .

[50]  Jesper Madsen,et al.  Flow topology and acoustic emissions of trailing edge serrations at incidence , 2016 .

[51]  Phillip Joseph,et al.  Towards a non-empirical trailing edge noise prediction model , 2016 .

[52]  V. Kibens,et al.  Passive Control of Jets with Indeterminate Origins , 1984 .

[53]  E. Fares,et al.  Evaluation of Airframe Noise Reduction Concepts via Simulations Using a Lattice Boltzmann Approach , 2015 .

[54]  C. F. Chen,et al.  The application of boundary layer independence principle to three-dimensional turbulent mixing layers , 2011, Journal of Fluid Mechanics.

[55]  M. Drela.  XFOIL: An Analysis and Design System for Low Reynolds Number Airfoils , 1989 .

[56]  Tze Pei Chong,et al.  On the aeroacoustic and flow structures developed on a flat plate with a serrated sawtooth trailing edge , 2015 .

[57]  Michel Roger,et al.  Back-scattering correction and further extensions of Amiet's trailing-edge noise model. Part II: Application , 2009 .

[58]  Daniele Ragni,et al.  Benefits of curved serrations on broadband trailing-edge noise reduction , 2017 .

[59]  Richard D. Sandberg,et al.  Investigation and prediction of transitional airfoil self-noise , 2009 .