Forced granular flow

The main goal of the thesis is to validate the ability of discrete element methods (DEM) to predict forced granular flow. Granular flow occurs in a broad spectrum of industrial applications. The thesis focuses on earthmoving processes typical of the mining and agricultural industries. Existing soil mechanics soil-tool models are also investigated and general flow behaviour in and around blades and buckets are established. Soil mechanics theories are used to predict the draft forces on a flat blade moving through granular material. Com and wheat grains are used as material. The rupture (slip) lines in front of the blade are predicted by soil mechanics and compared to experimental results. A two-dimensional test bench is used to visualise the flow of the granular material. Forces and moments that act on the tools are measured. DEM can be used to model industrial granular flow with large displacements. Two types of earthmoving equipment are simulated. The first is a flat blade and the second is a bucket. The forces on these tools are determined using DEM and compared to experimental results. The ability of DEM to predict material compressibility, the flow of material in and around the tools, the rupture lines and the bucket fill rate are investigated. A particle relative displacement method is used to determine the rupture lines. 11 Stellenbosch University http://scholar.sun.ac.za

[1]  J. C. Siemens,et al.  Mechanics of Soil as Influenced by Model Tillage Tools , 1965 .

[2]  P. Cundall,et al.  A discrete numerical model for granular assemblies , 1979 .

[3]  K H Head.  MANUAL OF SOIL LABORATORY TESTING: VOLUME 1, SECOND EDITION , 1992 .

[4]  K. S. Richards,et al.  Slope stability: Geotechnical engineering and geomorphology , 1987 .

[5]  R. L. Kushwaha,et al.  Three-dimensional, finite element interaction between soil and simple tillage tool , 1991 .

[6]  A. R. Reece,et al.  The calculation of passive soil resistance , 1974 .

[7]  Dr. Ir. Adrianus Jozef Koolen,et al.  Agricultural Soil Mechanics , 1983, Advanced Series in Agricultural Sciences.

[8]  A. Pecker,et al.  Ultimate bearing capacity of shallow foundations under inclined and eccentric loads. I: Purely cohesive soil , 1995 .

[9]  Albert-László Barabási,et al.  The physics of sand castles: maximum angle of stability in wet and dry granular media , 1999 .

[10]  Schalk Willem Petrus Esterhuyse.  The influence of geometry on dragline bucket filling performance , 1997 .

[11]  M. E. Merchant.  Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type 2 Chip , 1945 .

[12]  Albert-László Barabási,et al.  MAXIMUM ANGLE OF STABILITY IN WET AND DRY SPHERICAL GRANULAR MEDIA , 1997 .

[13]  Incipient failure in sandpile models , 1998, cond-mat/9812068.

[14]  Donald W. Taylor,et al.  Fundamentals of soil mechanics , 1948 .

[15]  T. Belytschko,et al.  Element‐free Galerkin methods , 1994 .

[16]  R. L. Kushwaha,et al.  Finite Element Analysis of the Dynamic Interaction Between Soil and Tillage Tool , 1995 .

[17]  Chandrakant S. Desai,et al.  Numerical Methods in Geotechnical Engineering , 1979 .

[18]  Edward McKyes.  The Calculation of Draft Forces and Soil Failure Boundaries of Narrow Cutting Blades , 1978 .

[19]  R. L. Braun,et al.  Viscosity, granular‐temperature, and stress calculations for shearing assemblies of inelastic, frictional disks , 1986 .

[20]  Paul W. Cleary,et al.  THREE-DIMENSIONAL MODELLING OF INDUSTRIAL GRANULAR FLOWS , 1999 .

[21]  M Reimbert,et al.  Silos theory and practice , 1976 .

[22]  Luc Oger,et al.  Internal Friction Angles: Characterization Using Biaxial Test Simulations , 1997 .