Surface micromachined PDMS microfluidic devices fabricated using a sacrificial photoresist

PDMS is a widely used material for construction of microfluidic devices. The traditional PDMS microfabrication process, although versatile, cannot be used to form microfluidic devices with embedded tall topological features, such as thick-film electrodes and porous reactor beds. This paper presents an elegant surface micromachining process for microfluidic devices that allows complete leak-proof sealing and a conformal contact of the PDMS with tall pre-existing topographical features and demonstrates this approach by embedding 6 ?m thick Ag/AgCl (high capacity 1680 ?A s) electrodes inside the microchannels. In this process, thin spin-cast films of the PDMS are used as the structural material and a photoresist is used as the sacrificial material. A crucial parameter, namely adhesion of the spun-cast structural layer to the substrate, was characterized for different pre-polymer ratios using a standard tensile test, and a 1:3 (curing agent:base) combination was found to be the best with a maximum adhesion strength of 7.2 MPa. The elastic property of the PDMS allowed extremely fast release times of ~1 min of the fabricated microchannels. The versatility of this process was demonstrated by the fabrication of a pneumatic microvalve with multi-layered microchannel geometry. The valve closure occurred at 6.37 kPa.

[1]  S. Quake,et al.  Monolithic microfabricated valves and pumps by multilayer soft lithography. , 2000, Science.

[2]  D. Beebe,et al.  Three-dimensional micro-channel fabrication in polydimethylsiloxane (PDMS) elastomer , 2000, Journal of Microelectromechanical Systems.

[3]  Teruo Fujii,et al.  Cell Culture in 3-Dimensional Microfluidic Structure of PDMS (polydimethylsiloxane) , 2003 .

[4]  Chang Liu,et al.  Re-configurable fluid circuits by PDMS elastomer micromachining , 1999, Technical Digest. IEEE International MEMS 99 Conference. Twelfth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.99CH36291).

[5]  D. Tokachichu,et al.  Bioadhesion of polymers for BioMEMS , 2006, IEEE Transactions on Nanotechnology.

[6]  Kwang-Seok Yun,et al.  Fabrication of complex multilevel microchannels in PDMS by using three-dimensional photoresist masters. , 2008, Lab on a chip.

[7]  E. Hutter,et al.  Exploitation of Localized Surface Plasmon Resonance , 2004 .

[8]  C. Henry,et al.  Conductivity detection for monitoring mixing reactions in microfluidic devices. , 2001, The Analyst.

[9]  R. Austin,et al.  Hydrodynamic Focusing on a Silicon Chip: Mixing Nanoliters in Microseconds , 1998 .

[10]  A. Majumdar,et al.  Spatially controlled microfluidics using low-voltage electrokinetics , 2006, Journal of Microelectromechanical Systems.

[11]  A. Ghatak,et al.  Embedded template-assisted fabrication of complex microchannels in PDMS and design of a microfluidic adhesive. , 2006, Langmuir : the ACS journal of surfaces and colloids.

[12]  Ching-Ping Wong,et al.  An improvement of thermal conductivity of underfill materials for flip-chip packages , 2003 .

[13]  Michael Kraft,et al.  Realization of electroplating molds with thick positive SPR 220-7 photoresist , 2003 .

[14]  A. Christensen,et al.  Characterization of interconnects used in PDMS microfluidic systems , 2005 .

[15]  A. Mata,et al.  Characterization of Polydimethylsiloxane (PDMS) Properties for Biomedical Micro/Nanosystems , 2005, Biomedical microdevices.

[16]  A. Majumdar,et al.  Stamp-and-stick room-temperature bonding technique for microdevices , 2005, Journal of Microelectromechanical Systems.

[17]  Y. Tai,et al.  Photoresist as a sacrificial layer by dissolution in acetone , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[18]  R. Zare,et al.  Construction of microfluidic chips using polydimethylsiloxane for adhesive bonding. , 2005, Lab on a chip.

[19]  C. Henry,et al.  Dual-electrode electrochemical detection for poly(dimethylsiloxane)-fabricated capillary electrophoresis microchips. , 2000, Analytical chemistry.

[20]  G. Whitesides,et al.  Poly(dimethylsiloxane) as a material for fabricating microfluidic devices. , 2002, Accounts of chemical research.

[21]  Chong H. Ahn,et al.  Institute of Physics Publishing Journal of Micromechanics and Microengineering a Review of Microvalves , 2022 .

[22]  C. H. Lee,et al.  Fabrication of thick electroforming micro mould using a KMPR negative tone photoresist , 2008 .

[23]  É. Favre.  Swelling of crosslinked polydimethylsiloxane networks by pure solvents: Influence of temperature , 1996 .

[24]  Dana M Spence,et al.  Fabrication of carbon microelectrodes with a micromolding technique and their use in microchip-based flow analyses. , 2004, The Analyst.

[25]  On-column amperometric detection for capillary electrophoresis microchips with electric field decoupler , 2002, 2nd Annual International IEEE-EMBS Special Topic Conference on Microtechnologies in Medicine and Biology. Proceedings (Cat. No.02EX578).

[26]  Senol Mutlu,et al.  Micromachined porous polymer for bubble free electro-osmotic pump , 2002, Technical Digest. MEMS 2002 IEEE International Conference. Fifteenth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.02CH37266).

[27]  Shaochen Chen,et al.  Polydimethylsioxane fluidic interconnects for microfluidic systems , 2003 .

[28]  J. Berg,et al.  Studies on surface wettability of poly(dimethyl) siloxane (PDMS) and glass under oxygen-plasma treatment and correlation with bond strength , 2005, Journal of Microelectromechanical Systems.

[29]  G. Whitesides,et al.  Rapid Prototyping of Microfluidic Systems in Poly(dimethylsiloxane). , 1998, Analytical chemistry.

[30]  Gwo-Bin Lee,et al.  Integrated microfluidic systems for cell lysis, mixing/pumping and DNA amplification , 2005 .

[31]  George M. Whitesides,et al.  Patterning the topographical environment for mammalian cell culture using laminar flows in capillaries , 2000, 1st Annual International IEEE-EMBS Special Topic Conference on Microtechnologies in Medicine and Biology. Proceedings (Cat. No.00EX451).

[32]  G. Whitesides,et al.  Solvent compatibility of poly(dimethylsiloxane)-based microfluidic devices. , 2003, Analytical chemistry.