Experimental diagnostics of ball bearings using statistical and spectral methods

Vibration measurements and signal analysis is widely used for condition monitoring of ball bearings as their vibration signature reveals important information about the defect development within them. Time domain analysis of vibration signature such as peak-to-peak amplitude, root mean square, Crest factor and kurtosis indicates defects in ball bearings. However, these measures do not specify the position and/or nature of the defects. Each defect produces characteristic vibrations in ball bearings. Hence, examining the vibration spectrum may deliver information on the type of defects. In this paper a test rig is designed and a pair of brand new commercial ball bearings is installed. The bearings run throughout their lifespan under constant speed and loading conditions. Vibration signatures produced are recorded and statistical measures are calculated during the test. When anomalies are detected in the statistical measures, vibration spectra are obtained and examined to determine where the defect is on the running surfaces. At the end of the test, the ball bearings are disassembled in order to take microscopic photos of the defects.

[1]  J. P. Yang,et al.  Vibration predictions and verifications of disk drive spindle system with ball bearings , 2002 .

[2]  Michael R. Hoeprich,et al.  Rolling Element Bearing Fatigue Damage Propagation , 1992 .

[3]  Steven Y. Liang,et al.  STOCHASTIC PROGNOSTICS FOR ROLLING ELEMENT BEARINGS , 2000 .

[4]  Homer Rahnejat,et al.  Vibration Modeling of Rotating Spindles Supported by Lubricated Bearings , 2002 .

[5]  J. Mathew,et al.  Frequency domain methods for monitoring the condition of rolling element bearings , 1985 .

[6]  J. Mathew,et al.  Time domain methods for monitoring the condition of rolling element bearings , 1985 .

[7]  A. W. Lees,et al.  Fault diagnosis of rotating machinery , 1998 .

[8]  Jun Ma,et al.  Detection of localised defects in rolling element bearings via composite hypothesis test , 1995 .

[9]  N. Tandon,et al.  An analytical model for the prediction of the vibration response of rolling element bearings due to a localized defect , 1997 .

[10]  Steven Y. Liang,et al.  Adaptive Prognostics for Rolling Element Bearing Condition , 1999 .

[11]  C. Cempel.  Condition evolution of machinery and its assessment from passive diagnostic experiment , 1991 .

[12]  Thomas R. Kurfess,et al.  Rolling element bearing diagnostics in run-to-failure lifetime testing , 2001 .

[13]  Yuling Yan,et al.  Application of the impulse index in rolling-element bearing fault diagnosis , 1992 .

[14]  K. V. Frolov,et al.  Vibroacoustical diagnostics for machines and structures , 1991 .

[15]  John T. Renwick.  Condition Monitoring of Machinery Using Computerized Vibration Signature Analysis , 1984, IEEE Transactions on Industry Applications.

[16]  N. Tandon,et al.  A review of vibration and acoustic measurement methods for the detection of defects in rolling element bearings , 1999 .

[17]  Czesław Cempel.  Vibroacoustical diagnostics of machinery: An outline , 1988 .

[18]  P. D. McFadden,et al.  Vibration monitoring of rolling element bearings by the high-frequency resonance technique — a review , 1984 .

[19]  T. A. Harris,et al.  Fatigue Failure Progression in Ball Bearings , 2001 .

[20]  H. Karagülle,et al.  Simulation and analysis of vibration signals generated by rolling element bearing with defects , 2003 .

[21]  S. A. McInerny,et al.  Basic vibration signal processing for bearing fault detection , 2003, IEEE Trans. Educ..

[22]  Oceans,et al.  Oceans engineering for today's technology and tomorrow's preservation : proceedings , 1994 .