Dimensional change of laser-welded gold alloy induced by heat treatment.

PURPOSE This study examined the effects of laser welding and heat treatment on the dimensional change of cast gold alloy frameworks. MATERIALS AND METHODS Pairs of cast gold alloy plates were matched, fixed in a jig, and welded in a laser-welding machine at constant welding parameters. The specimens were welded unilaterally (on one surface) or bilaterally (on two surfaces) with five spots as follows: two ends fixed/unilaterally welded (A); two ends fixed/bilaterally welded (AA); one end fixed/unilaterally welded (B); two ends fixed/welded on one surface and then one end fixed/welded on the opposite surface (AB); or one end fixed/bilaterally welded (BB). The dimensional change was determined by measuring the gap between the jig base and one end of the specimen after each welding application. Dimensional change was also measured after two different heat treatments (softening and hardening). The results were analyzed using a two-way ANOVA and Duncan's test (p < 0.05). RESULTS The dimensional change of the specimens fixed at only one end on either surface (AB, B, and BB) was higher compared with the two ends-fixed specimens (A and AA) after laser welding. The heat treatments also increased the dimensional change in all groups except for the B group. The dimensional change was similar for each fixing method between the two types of heat treatment. CONCLUSIONS The method of fixing the specimens in the jig significantly affected the amount of dimensional change of the gold alloys. The heat treatments of the laser-welded specimens increased the dimensional change by releasing the residual stress.

[1]  Tsukasa Akasaka,et al.  Distortion of laser welded titanium plates. , 2004, Dental materials journal.

[2]  Ikuya Watanabe,et al.  Tensile strength and elongation of laser-welded Ti and Ti-6AL-7NB. , 2004, Journal of biomedical materials research. Part B, Applied biomaterials.

[3]  M Atsuta,et al.  Mechanical strength of laser-welded cobalt-chromium alloy. , 2004, Journal of biomedical materials research. Part B, Applied biomaterials.

[4]  M Atsuta,et al.  Joint strength of laser-welded titanium. , 2002, Dental materials : official publication of the Academy of Dental Materials.

[5]  J. Liu,et al.  Effects of Heat Treatments on Mechanical Strength of laser-welded Equi-atomic AuCu-6at%Ga Alloy , 2001, Journal of dental research.

[6]  A. Carr,et al.  Distortion of three-unit implant frameworks during casting, soldering, and simulated porcelain firings. , 1999, Journal of prosthodontics : official journal of the American College of Prosthodontists.

[7]  T. Chai,et al.  Mechanical properties of laser-welded cast titanium joints under different conditions. , 1998, The Journal of prosthetic dentistry.

[8]  J. Chai,et al.  Mechanical properties of titanium connectors. , 1996, The International journal of prosthodontics.

[9]  S. Winkler,et al.  The effect of soldering, electrowelding, and cast-to procedures on the accuracy of fit of cast implant bars. , 1996, Implant dentistry.

[10]  G. Welsch,et al.  Joining titanium materials with tungsten inert gas welding, laser welding, and infrared brazing. , 1995, The Journal of prosthetic dentistry.

[11]  E. Dootz,et al.  Mechanical properties of laser-welded cast and wrought titanium. , 1995, The Journal of prosthetic dentistry.

[12]  T. Yamagishi,et al.  Mechanical properties of laser welds of titanium in dentistry by pulsed Nd:YAG laser apparatus. , 1993, The Journal of prosthetic dentistry.

[13]  J C Harter,et al.  Comparative accuracy of fixed partial dentures made as one-piece castings or joined by solder. , 1992, The International journal of prosthodontics.

[14]  J I Nicholls,et al.  Distortion in dental soldering as affected by gap distance. , 1980, The Journal of prosthetic dentistry.

[15]  John S. Huling,et al.  Comparative Distortion in Three-Unit Fixed Prostheses Joined by Laser Welding, Conventional Soldering, or Casting in One Piece , 1977, Journal of dental research.