Optimization of conformal cooling channels with array of baffles for plastic injection mold

Cooling system has an important role in the injection molding process in terms of not only productivity and quality, but also mold-making cost. In this paper, a conformal cooling channel with an array of baffles is proposed for obtaining uniform cooling over the entire free-form surface of molded parts. A new algorithm for calculating temperature distribution through molding thickness, mold surface temperature and cooling time was presented. The relation among cooling channels’ configuration, process parameters, mold material, molding thickness and temperature distribution in the mold for a given polymer is expressed by a system of approximate equations. This relation was established by the design of experiment and response surface methodology based on an adequate physical-mathematical model, finite difference method and numerical simulation. By applying this approximate mathematical relation, the optimization process for obtaining target mold temperature, uniform temperature distribution and minimizing the cooling time becomes more effective. Two case studies were carried out to test and validate the proposed method. The results show that present approach improves the cooling performance and facilitates the mold design process in comparison to the trial-and-error simulation-based method.

[1]  Singiresu S. Rao.  Engineering Optimization : Theory and Practice , 2010 .

[2]  Didier Delaunay,et al.  Study and modeling of heat transfer during the solidification of semi-crystalline polymers , 2005 .

[3]  Zone-Ching Lin,et al.  Design of the cooling channels in nonrectangular plastic flat injection mold , 2002 .

[4]  Huamin Zhou,et al.  An acceleration method for the BEM-based cooling simulation of injection molding , 2009 .

[5]  M. Cima,et al.  Production of injection molding tooling with conformal cooling channels using the three dimensional printing process , 2000 .

[6]  K. M. Yu,et al.  A scaffolding architecture for conformal cooling design in rapid plastic injection moulding , 2007 .

[7]  Constantin Chassapis,et al.  Optimal cooling system design for multi-cavity injection molding , 1997 .

[8]  H Zhou,et al.  Three-dimensional optimum design of the cooling lines of injection moulds based on boundary element design sensitivity analysis , 2002 .

[9]  S. Allen,et al.  The design of conformal cooling channels in injection molding tooling , 2001 .

[10]  Seong Jin Park,et al.  Thermal and Design Sensitivity Analyses for Cooling System of Injection Mold, Part 2: Design Sensitivity Analysis , 1998 .

[11]  Lars-Erik Rännar,et al.  Efficient cooling with tool inserts manufactured by electron beam melting , 2007 .

[12]  Gilles Régnier,et al.  Nature of contact between polymer and mold in injection molding. Part I: Influence of a non‐perfect thermal contact , 2000 .

[13]  Hae-Sim Park,et al.  Design of conformal cooling channels for an automotive part , 2009 .

[14]  Peter Kennedy,et al.  Practical and scientific aspects of injection molding simulation , 2008 .

[15]  D. Kazmer.  Injection Mold Design Engineering , 2007 .

[16]  Natti S. Rao,et al.  Optimization of Cooling Systems in Injection Molds by an Easily Applicable Analytical Model , 2002 .

[17]  Rémi Deterre,et al.  Change on temperature at the surface of injection moulded parts , 2010 .

[18]  Conor Hayes,et al.  FEA simulation of conformal cooling within injection moulds , 2007, Int. J. Manuf. Res..

[19]  Luiz C. Wrobel,et al.  A computational model for the cooling phase of injection moulding , 2008 .

[20]  Natti S. Rao.  Design formulas for plastics engineers , 1991 .

[21]  Jose M. Castro,et al.  A simplified approach to predict part temperature and minimum “safe” cycle time , 2008 .

[22]  Wen-Bin Young,et al.  Study on residual stresses of thin-walled injection molding , 2005 .

[23]  A. Mateus,et al.  Studies of rapid soft tooling with conformal cooling channels for plastic injection moulding , 2003 .

[24]  J. E. Sunderland,et al.  Thermal contact resistance in injection molding , 1990 .

[25]  Kang Tai,et al.  An evolutionary approach for cooling system optimization in plastic injection moulding , 2004 .

[26]  Huamin Zhou,et al.  Mold cooling simulation of the pressing process in TV panel production , 2005, Simul. Model. Pract. Theory.

[27]  A Y C Nee,et al.  The application of U-shape milled grooves for cooling of injection moulds , 2002 .

[28]  Zbigniew Michalewicz,et al.  Genetic algorithms + data structures = evolution programs (3rd ed.) , 1996 .

[29]  H. Qiao.  Transient mold cooling analysis using BEM with the time-dependent fundamental solution , 2005 .

[30]  Syed H. Masood,et al.  Cycle time optimization and part quality improvement using novel cooling channels in plastic injection moulding , 2009 .

[31]  J. E. Sunderland,et al.  Determination of ejection temperature and cooling time in injection molding , 1992 .

[32]  Cédric Le Bot,et al.  3D study of cooling system effect on the heat transfer during polymer injection molding , 2010 .

[33]  D. E. Dimla,et al.  Design and optimisation of conformal cooling channels in injection moulding tools , 2005 .

[34]  Andrew Y. C. Nee,et al.  Design and FEM analysis of the milled groove insert method for cooling of plastic injection moulds , 2004 .

[35]  Seong Jin Park,et al.  Thermal and Design Sensitivity Analyses for Cooling System of Injection Mold, Part 1: Thermal Analysis , 1998 .

[36]  K. A. Narh,et al.  Finite size gap effects on the modeling of thermal contact conductance at polymer-mold wall interface in injection molding , 2000 .

[37]  Kalyanmoy Deb,et al.  Multi-objective optimization using evolutionary algorithms , 2001, Wiley-Interscience series in systems and optimization.

[38]  A. Dawson,et al.  Polymer–mould interface heat transfer coefficient measurements for polymer processing , 2008 .

[39]  Jay Shoemaker,et al.  Moldflow Design Guide: A Resource for Plastics Engineers , 2006 .

[40]  H. Qiao.  A systematic computer-aided approach to cooling system optimal design in plastic injection molding , 2006 .

[41]  H. H. Chiang,et al.  Integrated Simulation of Fluid Flow and Heat Transfer in Injection Molding for the Prediction of Shrinkage and Warpage , 1993 .

[42]  Seong Jin Park,et al.  Optimal cooling system design for the injection molding process , 1998 .

[43]  Optimum cooling system design of a free-form injection mold using an abductive network , 2002 .

[44]  G. Menges,et al.  How to make injection molds , 1987 .

[45]  Rémi Deterre,et al.  Temperature measurements in the depth and at the surface of injected thermoplastic parts , 2005 .

[46]  Andreas Antoniou,et al.  Practical Optimization: Algorithms and Engineering Applications , 2007, Texts in Computer Science.

[47]  Abdelhakim Bendada,et al.  Analysis of thermal contact resistance between polymer and mold in injection molding , 2004 .

[48]  Sung-Chul Hwang,et al.  A study on the characteristic of parameters by the response surface method in final wafer polishing , 2009 .

[49]  Hamdy Hassan,et al.  Effect of cooling system on the polymer temperature and solidification during injection molding , 2009 .

[50]  Guoqun Zhao,et al.  Optimal design of heating channels for rapid heating cycle injection mold based on response surface and genetic algorithm , 2009 .