Numerical analysis of the influence of the channel cross-section aspect ratio on the performance of a PEM fuel cell with serpentine flow field design

Abstract This work numerically investigates the influence of the channel cross-section aspect ratio (defined as the ratio height/width) on the performance of a PEM fuel cell with serpentine flow field (SFF) design. The local current densities, velocity distributions, liquid water concentration in the membrane, hydrogen and oxygen concentrations and temperature were analyzed in the PEM fuel cell for 10 different aspect ratios, varying between 0.07 and 15, to understand the channel cross-section aspect ratio effect. The area of the channel cross section (1.06 mm 2 ) and the total effective reactive area of the PEM fuel cell (256 mm 2 ) were maintained constant in all cases. The obtained results show that at low operating voltages the cell performance is independent of the channel cross-section aspect ratio. At high operating voltages, where the influence of mass transporting velocity is predominant, as the channel cross-section aspect ratio increases the cell performance is improved. The models with high aspect ratio show, in general, more uniform current distributions, with the higher maximum and minimum intensity values, temperature distributions with smaller gradients and a superior contain of water in the membrane, which allows to obtain a higher performance. From these models the 10/06 and 12/05 aspect ratio present the best combination of variables, as shown by their polarization curves.

[1]  Hyung-Man Kim,et al.  Numerical studies on the geometrical characterization of serpentine flow-field for efficient PEMFC , 2011 .

[2]  Suk Won Cha,et al.  The scaling behavior of flow patterns: a model investigation , 2004 .

[3]  Gérard Gebel,et al.  Influence of PEMFC gas flow configuration on performance and water distribution studied by SANS: Evi , 2011 .

[4]  Suresh G. Advani,et al.  On the relative influence of convection in serpentine flow fields of PEM fuel cells , 2006 .

[5]  R. Mustata,et al.  Effect of the relative position of oxygen–hydrogen plate channels and inlets on a PEMFC , 2010 .

[6]  Byungki Ahn,et al.  Parametric study of the channel design at the bipolar plate in PEMFC performances , 2008 .

[7]  S. Shimpalee,et al.  Investigation of gas diffusion media inside PEMFC using CFD modeling , 2006 .

[8]  Xianguo Li,et al.  Review of bipolar plates in PEM fuel cells: Flow-field designs , 2005 .

[9]  Sirivatch Shimpalee,et al.  Numerical studies on rib & channel dimension of flow-field on PEMFC performance , 2007 .

[10]  K. McAuley,et al.  The effect of channel-to-channel gas crossover on the pressure and temperature distribution in PEM fuel cell flow plates , 2005 .

[11]  Effect of channel-to-channel cross-flow on local flooding in serpentine flow-fields , 2008 .

[12]  Sirivatch Shimpalee,et al.  Verifying Predictions of Water and Current Distributions in a Serpentine Flow Field Polymer Electrolyte Membrane Fuel Cell , 2003 .

[13]  Chang-Soo Kim,et al.  Effects of channel and rib widths of flow field plates on the performance of a PEMFC , 2005 .

[14]  Ay Su,et al.  A three-dimensional full-cell CFD model used to investigate the effects of different flow channel designs on PEMFC performance , 2007 .

[15]  Sirivatch Shimpalee,et al.  The impact of channel path length on PEMFC flow-field design , 2006 .

[16]  Sirivatch Shimpalee,et al.  Predicting water and current distributions in a commercial-size PEMFC , 2004 .

[17]  F. Büchi,et al.  Investigation of the Transversal Water Profile in Nafion Membranes in Polymer Electrolyte Fuel Cells , 2001 .

[18]  Sirivatch Shimpalee,et al.  The effect of serpentine flow-field designs on PEM fuel cell performance , 2008 .

[19]  Felix N. Büchi,et al.  Operating Proton Exchange Membrane Fuel Cells Without External Humidification of the Reactant Gases Fundamental Aspects , 1997 .

[20]  Tianshou Zhao,et al.  A new flow field design for polymer electrolyte-based fuel cells , 2007 .