Using short-time creep relaxation effect to decrease the residual stress in the bonded compliant seal of planar solid oxide fuel cell – A finite element simulation

Abstract Bonded compliant seal is a new sealing design for planar solid oxide fuel cell. During brazing, large residual stresses are generated which have a great effect on failure of the brazing connection. Therefore, how to decrease the residual stresses is a critical issue for structure integrity. This paper presents a study on decreasing residual stresses by using short-time creep relaxation effect. A sequential-coupled calculation model is developed based on finite element method. The brazing temperature field is firstly obtained by simulating the convection and radiation heating, and then the residual stress is calculated by a thermal-elasto-plastic-creep model. The calculated results are verified by neutron diffraction measurements. During cooling, a short holding time at 600 °C is designed to relax the residual stress by creep effect. The results show that this effect has a remarkable impact on decreasing the residual stress. The stresses in cell, Ag–CuO and foil have been reduced by about 26.9%, 13.6% and 22.1%, respectively, as the holding time increases up to 40 h. When the holding time exceeds 40 h, the residual stresses remain almost unchanged. It is thus suggested that the holding time should be reasonably determined to allow sufficient stress relaxation.

[1]  D. Clarke,et al.  Vibration damping of superalloys and thermal barrier coatings at high-temperatures , 2007 .

[2]  Brian J. Koeppel,et al.  Comparative finite element analysis of the stress-strain states in three different bonded solid oxide fuel cell seal designs , 2008 .

[3]  Francois L. E. Usseglio-Viretta,et al.  Creep behaviour of porous SOFC electrodes: Measurement and application to Ni-8YSZ cermets , 2011 .

[4]  Liu Tiejun,et al.  Determining the mechanical properties of solid oxide fuel cell by an improved work of indentation approach , 2012 .

[5]  A. Nakajo,et al.  Modeling of thermal stresses and probability of survival of tubular SOFC , 2006 .

[6]  G. Li,et al.  Residual stress and plastic strain analysis in the brazed joint of bonded compliant seal design in planar solid oxide fuel cell , 2010 .

[7]  Jianming Gong,et al.  Effect of holding time on vacuum brazing for a stainless steel plate–fin structure , 2010 .

[8]  S. Tu,et al.  Three-dimensional simulation to study the influence of foil thickness on residual stress in the bonded compliant seal design of planar solid oxide fuel cell , 2012 .

[9]  S. Tu,et al.  A new cooling method for vacuum brazing of a stainless steel plate–fin structure , 2010 .

[10]  Tsung Leo Jiang,et al.  Thermal-stress analyses of an operating planar solid oxide fuel cell with the bonded compliant seal design , 2009 .

[11]  S. Tu,et al.  Effect of Al2O3 film on thermal stress in the bonded compliant seal design of planar solid oxide fuel cell , 2011 .

[12]  G. Subbarayan,et al.  Thermo-elastic properties of dense YSZ and porous Ni-ZrO2 monolithic and isotropic materials , 2006 .

[13]  D. Tréheux,et al.  Effect of thermal residual stresses on the strength for both alumina/Ni/alumina and alumina/Ni/nickel alloy bimaterials , 2009 .

[14]  Z. Hu,et al.  High temperature creep and low cycle fatigue of a nickel-base superalloy , 2010 .

[15]  Yixing Yuan,et al.  Effective Ag–CuO sealant for planar solid oxide fuel cells , 2010 .

[16]  C. Leinenbach,et al.  Thermomechanical analysis of residual stresses in brazed diamond metal joints using Raman spectroscopy and finite element simulation , 2012 .

[17]  S. Bull.  Modeling of Residual Stress in Oxide Scales , 1998 .

[18]  I. Yasuda,et al.  3-D model calculation for planar SOFC , 2001 .

[19]  Lieh-Kwang Chiang,et al.  Thermo-electrochemical and thermal stress analysis for an anode-supported SOFC cell , 2008 .

[20]  Lieh-Kwang Chiang,et al.  Thermal stress analysis of a planar SOFC stack , 2007 .

[21]  Sea-Fue Wang,et al.  Effect of additives on the thermal properties and sealing characteristic of BaO-Al2O3-B2O3-SiO2 glass-ceramic for solid oxide fuel cell application , 2009 .

[22]  Pierre Bleuet,et al.  Determination of global and local residual stresses in SOFC by X-ray diffraction , 2010 .

[23]  Dan Eliezer,et al.  The applicability of Norton's creep power law and its modified version to a single-crystal superalloy type CMSX-2 , 1996 .

[24]  G. An,et al.  Neutron diffraction measurements of residual stresses in a 50 mm thick weld , 2011 .

[25]  B. Koeppel,et al.  Thermal stress analysis of the planar SOFC bonded compliant seal design , 2008 .

[26]  Gunther Eggeler,et al.  A creep finite element analysis of indentation creep testing in two phase microstructures (particle/matrix- and thin film/substrate-systems) , 2001 .