The microfabrication of capacitive ultrasonic transducers

Surface-micromachined capacitive ultrasonic transducers, which are suitable for operation in both air and water, have been fabricated and tested. Amorphous silicon is used as a sacrificial layer because of its good etching selectivity versus a nitride membrane, and improved cell-size control is obtained by lithographic definition of cavity walls. In addition, appropriate feature designs based on two-dimensional (2-D) process simulations make it possible to achieve device cavity sealing with g-line optical lithography. Transmission experiments in both water and air are presented. A dynamic range in excess of 110 dB is observed in air at 2.3 MHz. In water, a single pair of transducers is able to operate from 2 to 15 MHz. When tuned, a 3.5-MHz tone burst results in a received signal with better than 60-dB signal-to-noise ratio (SNR). The transducer behaviour agrees with a theoretical understanding of transducer dynamics. The dynamic ranges achieved in this paper are the best reported to date for surface-micromachined capacitive ultrasonic transducers.

[1]  Christofer Hierold,et al.  Surface micromachined ultrasound transducers in CMOS technology , 1996, 1996 IEEE Ultrasonics Symposium. Proceedings.

[2]  C Wykes,et al.  The performance of capacitive ultrasonic transducers using v-grooved backplates , 1991 .

[3]  D. Schindel,et al.  The design and characterization of micromachined air-coupled capacitance transducers , 1995, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[4]  A. G. Bashford,et al.  Characteristics of ultrasonic micromachined capacitance transducers in water , 1996, 1996 IEEE Ultrasonics Symposium. Proceedings.

[5]  B. Khuri-Yakub,et al.  Surface micromachined capacitive ultrasonic transducers , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[6]  K. Suzuki,et al.  A silicon electrostatic ultrasonic transducer , 1989, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[7]  K. Sasaki,et al.  Electroacoustic model for electrostatic ultrasonic transducers with V-grooved backplates , 1995, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[8]  Gisela Hess,et al.  A subminiature condenser microphone with silicon nitride membrane and silicon back plate , 1989 .

[9]  Butrus T. Khuri-Yakub,et al.  Micromachined ultrasonic transducers: 11.4 MHz transmission in air and more , 1996 .

[10]  Abdullah Atalar,et al.  Silicon micromachined ultrasonic immersion transducers , 1996 .

[11]  Michael J. Anderson,et al.  BROADBAND ELECTROSTATIC TRANSDUCERS : MODELING AND EXPERIMENTS , 1995 .

[12]  G. Kino.  Acoustic waves : devices, imaging, and analog signal processing , 1987 .

[13]  I. Ladabaum,et al.  Micromachined ultrasonic transducers (MUTs) , 1995, 1995 IEEE Ultrasonics Symposium. Proceedings. An International Symposium.

[14]  B. Khuri-Yakub,et al.  Micromachined 2-D array piezoelectrically actuated flextensional transducers , 1997, 1997 IEEE Ultrasonics Symposium Proceedings. An International Symposium (Cat. No.97CH36118).

[15]  B. Khuri-Yakub,et al.  A surface micromachined electrostatic ultrasonic air transducer , 1996, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[16]  K.K. Li,et al.  Micromachined high frequency ferroelectric sonar transducers , 1997, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[17]  R.M. White,et al.  Plate-Mode Ultrasonic Oscillator Sensors , 1987, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.