Piezoelectric properties of zinc oxide films on glass substrates deposited by RF-magnetron-mode electron cyclotron resonance sputtering system

There are various types of electron cyclotron resonance (ECR) sputtering systems, DC-mode, RF-mode, etc. We reported that zinc oxide (ZnO) films on glass substrates deposited by DC-mode ECR and RF-mode ECR sputtering systems had shown excellent piezoelectric properties and c-axis orientations. The RF-mode ECR sputtering system was capable of depositing ZnO films on glass substrates without evidence of column and fiber grains in cross section and driving a 1.1 GHz fundamental Rayleigh surface acoustic wave (SAW). In this paper, the properties of ZnO film deposited by an RF-magnetron-mode ECR sputtering system, which has added magnets to the outside of a cylindrical zinc metal (Zn) target of the RF-mode ECR sputtering system, are investigated. It is confirmed that the SAW filters using ZnO films on an interdigital transducer (IDT)/glass substrate deposited by the RF-magnetron-mode ECR sputtering exhibit almost the same effective electromechanical coupling factors (keff) as the theoretical keff values calculated by finite element method (FEM) using the constants of ZnO single crystal (measured keff values are 97% of the theoretical values) and 0.6/spl sim/3.7 dB lower insertion loss in comparison with the films deposited by the DC-mode ECR and the RF-mode ECR sputtering system.<<ETX>>

[1]  H. M. Gerard,et al.  Analysis of Interdigital Surface Wave Transducers by Use of an Equivalent Circuit Model , 1969 .

[2]  S. Matsuo,et al.  Reactive Ion Beam Etching Using a Broad Beam ECR Ion Source , 1982 .

[3]  N. Chubachi,et al.  Physical Structure of DC Diode Sputtered ZnO Films and its Influence on the Effective Electromechanical Coupling Factors , 1974 .

[4]  J.J. Campbell,et al.  A method for estimating optimal crystal cuts and propagation directions for excitation of piezoelectric surface waves , 1968, IEEE Transactions on Sonics and Ultrasonics.

[5]  R. Schmidt,et al.  Piezoelectric Elastic Surface Waves in Anisotropic Layered Media , 1969 .

[6]  Akira Kawabata,et al.  Characterization of ZnO piezoelectric films prepared by rf planar‐magnetron sputtering , 1980 .

[7]  Makoto Minakata,et al.  Characteristics of Zinc Oxide Films on Glass Substrates Deposited by RF-Mode Electron Cyclotron Resonance Sputtering System , 1993 .

[8]  M. Koshiba,et al.  Equivalent networks for SAW gratings , 1988, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[9]  F. Hickernell.  ZnO Processing for Bulk- and Surface-Wave Devices , 1980 .

[10]  N. Chubachi,et al.  Thickness dependence of effective coupling factors of ZnO thin-film surface-wave transducers , 1973 .

[11]  M. Kadota,et al.  Characteristics of piezoelectric ZnO films deposited by RF mode electron cyclotron resonance sputtering system , 1992 .

[12]  Michio Kadota,et al.  Evaluation of Glass Substrates for SAW Filters by Acoustic Microscopy Technique , 1991 .

[13]  M. Kadota,et al.  The Polishing Effect of ZnO Thin Films on SAW Filters , 1990 .

[14]  M. Sayer,et al.  Position and pressure effects in rf magnetron reactive sputter deposition of piezoelectric zinc oxide , 1984 .

[15]  Makoto Minakata,et al.  Piezoelectric Characteristics of ZnO Films Deposited Using an Electron Cyclotron Resonance Sputtering System , 1992 .

[16]  W. Pedler,et al.  Fundamental- and Harmonic-Frequency Circuit-Model Analysis of Lnterdigital Transducers with Arbitralry Metallization Ratios and Polarity Sequences , 1975 .