Interlaminar Fracture of Commingled GF/PET Composite Laminates

The Mode I, Mode II and mixed mode (Mode I:II ratios of 4:1, 1:1 and 1:4) fracture behavior of novel textile glass fiber reinforced polyethylene terephthalate (GF/PET) laminates has been investigated. The laminates were manufactured by compression molding two different fabrics produced by weaving and warp knitting commingled GF/PET yarns. The initiation fracture toughness of the woven laminates in pure Mode I and Mode II were slightly higher than those of the warp knitted laminates. For the mixed modes, the difference between the fracture toughness of the two materials was smaller. An extensive scanning electron microscopy (SEM) investigation of the fracture was conducted to identify any characteristic failure mechanisms. The main fractographic features of the Mode I dominated failures were a brittle matrix failure and large amounts of fiber pull-out. As the Mode II loading component increased, the amount of fiber pull-out was reduced and the matrix had a more sheared appearance. A relatively large amount of cusps were found in pure Mode II and mixed mode I:II = 1:4; such features are seldom seen in thermoplastic matrix composites. A general mixed mode failure criterion, which accounts for the appearance of the fracture surface, was evaluated and was seen to give a good fit to the experimental fracture toughness values.

[1]  L. Ye,et al.  Interlaminar fracture of commingled-fabric-based GF/PET composites , 1993 .

[2]  H. Hamada,et al.  The effect of impregnation technique on bending properties of glass fiber reinforced polyethylene terephthalate composites , 1994 .

[3]  M. Gilchrist,et al.  Fabrication and mechanical response of commingled GF/PET composites , 1998 .

[4]  J. Masters,et al.  Fractography of Modern Engineering Materials: Composites and Metals, Second Volume , 1993 .

[5]  IS ABSOLVED,et al.  Royal Aircraft Establishment , 1959, Nature.

[6]  J. G. Williams,et al.  On the analysis of mixed-mode failure , 1992, International Journal of Fracture.

[7]  L. Ye,et al.  Consolidation of GF/PP commingled yarn composites , 1994 .

[8]  L. Ye,et al.  Influence of cooling rate on interlaminar fracture properties of unidirectional commingled CF/PEEK composites , 1995 .

[9]  J. G. Williams,et al.  The mixed-mode delamination of fibre composite materials , 1993 .

[10]  T. Johannesson,et al.  The detailed structure of delamination fracture surfaces in graphite/epoxy laminates , 1984 .

[11]  L. Ye,et al.  Interlaminar fracture (model II) of commingled yarn-based GF/PP composites , 1993 .

[12]  L. Ye,et al.  Mode I interlaminar fracture of co-mingled yarn based glass/polypropylene composites , 1993 .

[13]  H. Yoon,et al.  Mode I interlaminar fracture toughness of commingled carbon fibre/PEEK composites , 1993, Journal of Materials Science.

[14]  Michael D. Gilchrist,et al.  MIXED-MODE DELAMINATION OF MULTIDIRECTIONAL CARBON FIBER/EPOXY LAMINATES , 1998 .

[15]  L. Ye,et al.  Role of cooling pressure on interlaminar fracture properties of commingled CF/PEEK composites , 1996 .

[16]  J. Masters,et al.  Fractography of modern engineering materials : composites and metals : a symposium , 1987 .

[17]  Michael D. Gilchrist,et al.  A fractographic analysis of delamination within multidirectional carbon/epoxy laminates , 1995 .

[18]  P A Smith,et al.  ON THE APPLICATION OF FRACTURE MECHANICS TO COMPOSITE MATERIALS , 2000 .

[19]  Michael D. Gilchrist,et al.  Manufacturing of Thermoplastic Composites from Commingled Yarns-A Review , 1998 .

[20]  W. S. Johnson.  Delamination and Debonding of Materials , 1985 .

[21]  M. Benzeggagh,et al.  Measurement of mixed-mode delamination fracture toughness of unidirectional glass/epoxy composites with mixed-mode bending apparatus , 1996 .

[22]  Y. Mai,et al.  Mode I delamination and fibre bridging in carbon-fibre/epoxy composites with and without PVAL coating , 1993 .

[23]  L. Ye,et al.  Consolidation and Interlaminar Fracture Properties of Unidirectional Commingled CF/PEEK Composites , 1996 .