Design and experimental characterization of an electromagnetic transducer for large-scale vibratory energy harvesting applications

This article reports on the design and experimental characterization of an electromagnetic transducer for energy harvesting from large structures (e.g., multistory buildings and bridges), for which the power levels can be above 100 W and disturbance frequencies below 1 Hz. The transducer consists of a back-driven ballscrew coupled to a permanent-magnet synchronous machine with power harvesting regulated via control of a four-quadrant power electronic drive. Design considerations between various subsystems are illustrated and recommendations in terms of minimal values are made for each design metric. Developing control algorithms to take full advantage of the unique features of this type of transducer requires a mechanical model that can adequately characterize the device’s intrinsic nonlinear behavior. A new model is proposed that can effectively capture this behavior. Comparison with experimental results verifies that the model is accurate over a wide range of operating conditions. As such, the model can be used to assess the viability of the technology and to correctly design controllers to maximize power generation. To demonstrate the device’s energy harvesting capability, impedance matching theory is used to optimize the power generated from a base-excited tuned mass damper. Both theoretical and experimental investigations are compared and the results are shown to match closely.

[1]  D. Inman,et al.  Resistive Impedance Matching Circuit for Piezoelectric Energy Harvesting , 2010 .

[2]  Sam Behrens,et al.  Adaptive learning algorithms for vibration energy harvesting , 2008 .

[3]  Norman M. Wereley,et al.  Self-Powered Magnetorheological Dampers , 2009 .

[4]  Neil M. White,et al.  An electromagnetic, vibration-powered generator for intelligent sensor systems , 2004 .

[5]  Jeffrey T. Scruggs,et al.  Design of electromagnetic energy harvesters for large-scale structural vibration applications , 2011, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[6]  Bernard H. Stark,et al.  MEMS electrostatic micropower generator for low frequency operation , 2004 .

[7]  Yu Zhou,et al.  Design and characterization of an electromagnetic energy harvester for vehicle suspensions , 2010 .

[8]  Y. Wen.  Method for Random Vibration of Hysteretic Systems , 1976 .

[9]  Rajeevan Amirtharajah,et al.  Self-powered signal processing using vibration-based power generation , 1998, IEEE J. Solid State Circuits.

[10]  Kenneth Levenberg.  A METHOD FOR THE SOLUTION OF CERTAIN NON – LINEAR PROBLEMS IN LEAST SQUARES , 1944 .

[11]  Lei Zuo,et al.  Simulation and experiment validation of simultaneous vibration control and energy harvesting from buildings using Tuned Mass Dampers , 2011, Proceedings of the 2011 American Control Conference.

[12]  Henry A. Sodano,et al.  A review of power harvesting using piezoelectric materials (2003–2006) , 2007 .

[13]  Henry A. Sodano,et al.  Structural Effects and Energy Conversion Efficiency of Power Harvesting , 2009 .

[14]  Billie F. Spencer,et al.  Large-scale MR fluid dampers: modeling and dynamic performance considerations , 2002 .

[15]  D. Marquardt.  An Algorithm for Least-Squares Estimation of Nonlinear Parameters , 1963 .

[16]  Norman M. Wereley,et al.  Analysis and testing of Bingham plastic behavior in semi-active electrorheological fluid dampers , 1996 .

[17]  N. G. Stephen.  On the maximum power transfer theorem within electromechanical systems , 2006 .

[18]  Ahsan Kareem,et al.  Assessment of Energy Potential and Vibration Mitigation of Regenerative Tuned Mass Dampers on Wind Excited Tall Buildings , 2011 .

[19]  D. Gamota,et al.  Dynamic mechanical studies of electrorheological materials: Moderate frequencies , 1991 .

[20]  Shirley J. Dyke,et al.  PHENOMENOLOGICAL MODEL FOR MAGNETORHEOLOGICAL DAMPERS , 1997 .

[21]  Malcolm C. Smith.  Synthesis of mechanical networks: the inerter , 2002, IEEE Trans. Autom. Control..

[22]  D. Guyomar,et al.  Buck-Boost Converter for Sensorless Power Optimization of Piezoelectric Energy Harvester , 2007, IEEE Transactions on Power Electronics.

[23]  Jerome J. Connor,et al.  Feasibility Study of Passive Electromagnetic Damping Systems , 2008 .

[24]  Jan M. Rabaey,et al.  A study of low level vibrations as a power source for wireless sensor nodes , 2003, Comput. Commun..

[25]  Robert D. Hanson,et al.  Electrorheological Dampers, Part II: Testing and Modeling , 1996 .

[26]  Martin S. Williams,et al.  REAL-TIME SUBSTRUCTURE TESTS USING HYDRAULIC ACTUATOR , 1999 .

[27]  Jeffrey T. Scruggs,et al.  Control of a Civil Structure Using an Electric Machine with Semiactive Capability , 2003 .

[28]  O. Korostynska.  Energy Harvesting Technologies , 2011 .

[29]  Pragasen Pillay,et al.  Modeling, simulation, and analysis of permanent-magnet motor drives. I. The permanent-magnet synchronous motor drive , 1989 .

[30]  R. Krishnan,et al.  A Strategy for Active Control of Tall Civil Structures Using Regenerative Electric Actuators , 1996 .

[31]  Jeffrey T. Scruggs,et al.  Structural control with regenerative force actuation networks , 2005 .