Time-optimized X-ray micro-CT imaging of polymer based scaffolds.

Although X-ray microscopic computed tomography is widely used to assess the structural properties of polymeric tissue scaffolds its validity is dependent on the quality of the images obtained. Here, the role of resolution, integration time, image averaging, and X-ray power on the accurate determination of scaffold porosity, while aiming to minimize imaging time, was investigated. This work identified key parameters for optimization and a methodology to vary them to improve results. Based on this, guidelines were developed to assist in the selection of image acquisition parameters to allow rapid and accurate scaffold imaging as required for mass manufacture.

[1]  A. D'Amore,et al.  Characterization of the complete fiber network topology of planar fibrous tissues and scaffolds. , 2010, Biomaterials.

[2]  P Cloetens,et al.  Regularized phase tomography enables study of mineralized and unmineralized tissue in porous bone scaffold , 2010, Journal of microscopy.

[3]  J. Crowe,et al.  Generation and simulated imaging of pseudo-scaffolds to aid characterisation by X-ray micro CT. , 2009, Biomaterials.

[4]  Richard A. Robb,et al.  Image-based structure-to-function correlation of tissue engineering scaffolds , 2009, 2009 IEEE International Symposium on Biomedical Imaging: From Nano to Macro.

[5]  D. Hutmacher,et al.  The correlation of pore morphology, interconnectivity and physical properties of 3D ceramic scaffolds with bone ingrowth. , 2009, Biomaterials.

[6]  K. Shakesheff,et al.  Image-based characterization of foamed polymeric tissue scaffolds , 2008, Biomedical materials.

[7]  Dietmar W Hutmacher,et al.  Assessment of bone ingrowth into porous biomaterials using MICRO-CT. , 2007, Biomaterials.

[8]  John A Crowe,et al.  Meeting the needs of monitoring in tissue engineering. , 2007, Regenerative medicine.

[9]  Andrei L. Turinsky,et al.  Effect of Voxel Size on 3D Micro-CT Analysis of Cortical Bone Porosity , 2007, Calcified Tissue International.

[10]  Dominique Bernard,et al.  Non-destructive quantitative 3D analysis for the optimisation of tissue scaffolds. , 2007, Biomaterials.

[11]  Dietmar W Hutmacher,et al.  A comparison of micro CT with other techniques used in the characterization of scaffolds. , 2006, Biomaterials.

[12]  Richard Archer,et al.  Why tissue engineering needs process engineering , 2005, Nature Biotechnology.

[13]  Dietmar W Hutmacher,et al.  Analysis of 3D bone ingrowth into polymer scaffolds via micro-computed tomography imaging. , 2004, Biomaterials.

[14]  Wei Sun,et al.  3D microtomographic characterization of precision extruded poly-epsilon-caprolactone scaffolds. , 2004, Journal of biomedical materials research. Part B, Applied biomaterials.

[15]  Andrei L. Turinsky,et al.  Quantitative 3D analysis of the canal network in cortical bone by micro-computed tomography. , 2003, Anatomical record. Part B, New anatomist.

[16]  W. Lindquist,et al.  Image Thresholding by Indicator Kriging , 1999, IEEE Trans. Pattern Anal. Mach. Intell..

[17]  S. Majumdar,et al.  Impact of spatial resolution on the prediction of trabecular architecture parameters. , 1998, Bone.

[18]  P Rüegsegger,et al.  Resolution dependency of microstructural properties of cancellous bone based on three-dimensional mu-tomography. , 1996, Technology and health care : official journal of the European Society for Engineering and Medicine.

[19]  Thierry Pun,et al.  A new method for grey-level picture thresholding using the entropy of the histogram , 1980 .

[20]  Z. Tabor.  Analysis of the influence of image resolution on the discriminating power of trabecular bone architectural parameters. , 2004, Bone.

[21]  N. Otsu.  A threshold selection method from gray level histograms , 1979 .