A high efficient assembly technique for large PEMFC stacks: Part I. Theory

A high efficient assembly technique for large proton exchange membrane fuel cell (PEMFC) stacks is proposed to obtain the optimal clamping load. The stack system is considered as a mechanical equivalent stiffness model consisting of numerous elastic elements (springs) in either series or parallel connections. We first propose an equivalent stiffness model for a single PEM fuel cell, and then develop an equivalent stiffness model for a large PEMFC stack. Based on the equivalent stiffness model, we discuss the effects of the structural parameters and temperature on the internal stress of the components and the contact resistance at the contact interfaces, and show how to determine the assembly parameters of a large fuel cell stack using the equivalent stiffness model. Finally, a three-dimensional finite element analysis (FEA) for a single PEMFC is compared with what the equivalent stiffness model predicts. It is found that the presented model gives very good prediction accuracy for the component stiffness and the clamping load.

[1]  Myoungho Sunwoo,et al.  A lumped parameter model of the polymer electrolyte fuel cell , 2007 .

[2]  Ying Wang,et al.  The dynamic behavior of pressure during purge process in the anode of a PEM fuel cell , 2006 .

[3]  P. Sui,et al.  A numerical investigation of the effects of compression force on PEM fuel cell performance , 2008 .

[4]  Michael H. Santare,et al.  Stresses in Proton Exchange Membranes Due to Hygro-Thermal Loading , 2006 .

[5]  D. A. Bograchev,et al.  Stress and plastic deformation of MEA in fuel cells: Stresses generated during cell assembly , 2008 .

[6]  Hyung Jin Sung,et al.  Effect of GDL permeability on water and thermal management in PEMFCs—II. Clamping force , 2008 .

[7]  N. Djilali,et al.  Effect of compression on liquid water transport and microstructure of PEMFC gas diffusion layers , 2007 .

[8]  W. B. Johnson,et al.  Mechanical response of fuel cell membranes subjected to a hygro-thermal cycle , 2006 .

[9]  W. B. Johnson,et al.  Mechanical behavior of fuel cell membranes under humidity cycles and effect of swelling anisotropy on the fatigue stresses , 2007 .

[10]  Marc Thomas,et al.  Equivalent Stiffness and Damping Investigation of a Hydrostatic Journal Bearing , 2007 .

[11]  Viral S. Mehta,et al.  Review and analysis of PEM fuel cell design and manufacturing , 2003 .

[12]  F. de Bruijn,et al.  Review: Durability and Degradation Issues of PEM Fuel Cell Components , 2008 .

[13]  Chengwei Wu,et al.  Numerical study on the compression effect of gas diffusion layer on PEMFC performance , 2007 .

[14]  Sandip Mazumder,et al.  Numerical investigation of the effect of cathode catalyst layer structure and composition on polymer electrolyte membrane fuel cell performance , 2008 .

[15]  Chengwei Wu,et al.  Contact resistance prediction and structure optimization of bipolar plates , 2006 .

[16]  Chengwei Wu,et al.  Influence of clamping force on the performance of PEMFCs , 2007 .

[17]  Ching-Han Huang,et al.  Analyses of the fuel cell stack assembly pressure , 2005 .

[18]  Jun Ni,et al.  A mechanical-electrical finite element method model for predicting contact resistance between bipolar plate and gas diffusion layer in PEM fuel cells , 2008 .

[19]  K. Hertwig,et al.  Mathematical Modelling and Simulation of Polymer Electrolyte Membrane Fuel Cells. Part I: Model Structures and Solving an Isothermal One‐Cell Model , 2002 .

[20]  S. Timoshenko,et al.  Theory of elasticity , 1975 .