Modeling and fabrication of prosthetic sockets using selective laser sintering

[1]  Richard H. Crawford,et al.  Clinical Evaluation of Prosthetic Sockets Manufactured by Selective Laser Sintering , 2001 .

[2]  A W Buis,et al.  Conventional patellar-tendon-bearing (PTB) socket/stump interface dynamic pressure distributions recorded during the prosthetic stance phase of gait of a transtibial amputee , 1998, Prosthetics and orthotics international.

[3]  R. Seymour.  Prosthetics and orthotics : lower limb and spinal , 2002 .

[4]  A F Mak,et al.  State-of-the-art research in lower-limb prosthetic biomechanics-socket interface: a review. , 2001, Journal of rehabilitation research and development.

[5]  M. Zhang,et al.  Comparison of computational analysis with clinical measurement of stresses on below-knee residual limb in a prosthetic socket. , 2000, Medical engineering & physics.

[6]  S G Zachariah,et al.  Effects of changes in cadence, prosthetic componentry, and time on interface pressures and shear stresses of three trans-tibial amputees. , 2000, Clinical biomechanics.

[7]  V. C. Roberts,et al.  Frictional action at lower limb/prosthetic socket interface. , 1996, Medical engineering & physics.

[8]  G Simpson,et al.  Modeling the interactions between a prosthetic socket, polyurethane liners and the residual limb in transtibial amputees using non-linear finite element analysis. , 2001, Biomedical sciences instrumentation.

[9]  D G Smith,et al.  Socket considerations for the patient with a transtibial amputation. , 1999, Clinical orthopaedics and related research.

[10]  C H Daly,et al.  Interface pressures and shear stresses: Sagittal plane angular alignment effects in three trans-tibial amputee case studies , 1999, Prosthetics and orthotics international.

[11]  S G Zachariah,et al.  Interface mechanics in lower-limb external prosthetics: a review of finite element models. , 1996, IEEE transactions on rehabilitation engineering : a publication of the IEEE Engineering in Medicine and Biology Society.

[12]  M B Silver-Thorn,et al.  Investigation of lower-limb tissue perfusion during loading. , 2002, Journal of rehabilitation research and development.

[13]  J. Petersson,et al.  Numerical instabilities in topology optimization: A survey on procedures dealing with checkerboards, mesh-dependencies and local minima , 1998 .

[14]  R. Crawford,et al.  Testing of Compliance in a Prosthetic Socket Fabricated Using Selective Laser Sintering , 2001 .

[15]  G. Rozvany.  Stress ratio and compliance based methods in topology optimization – a critical review , 2001 .

[16]  N. Kikuchi,et al.  A homogenization method for shape and topology optimization , 1991 .

[17]  W. Lee,et al.  Load transfer mechanics between trans-tibial prosthetic socket and residual limb--dynamic effects. , 2004, Journal of biomechanics.

[18]  S G Zachariah,et al.  Finite element estimates of interface stress in the trans-tibial prosthesis using gap elements are different from those using automated contact. , 2000, Journal of biomechanics.

[19]  Donald Freeman,et al.  Stereolithography and Prosthetic Test Socket Manufacture: A Cost/Benefit Analysis , 1998 .

[20]  Jack L. Lancaster,et al.  A Computerized System to Manufacture Prostheses for Amputees in Developing Countries , 1989 .

[21]  Sridhar Kota,et al.  An Energy Formulation for Parametric Size and Shape Optimization of Compliant Mechanisms , 1999 .

[22]  Joseph J. Beaman,et al.  Fabrication of Prosthetic Socket by Selective Laser Sintering , 1991 .

[23]  K. Svanberg.  The method of moving asymptotes—a new method for structural optimization , 1987 .

[24]  M. Bendsøe,et al.  Material interpolation schemes in topology optimization , 1999 .

[25]  S G Zachariah,et al.  Automated hexahedral mesh generation from biomedical image data: applications in limb prosthetics. , 1996, IEEE transactions on rehabilitation engineering : a publication of the IEEE Engineering in Medicine and Biology Society.

[26]  A W Buis,et al.  Calibration problems encountered while monitoring stump/socket interface pressures with force sensing resistors: Techniques adopted to minimise inaccuracies , 1997, Prosthetics and orthotics international.

[27]  M B Silver-Thorn,et al.  In vivo indentation of lower extremity limb soft tissues. , 1999, IEEE transactions on rehabilitation engineering : a publication of the IEEE Engineering in Medicine and Biology Society.

[28]  Ole Sigmund,et al.  A 99 line topology optimization code written in Matlab , 2001 .

[29]  M Zhang,et al.  Finite element modelling of a residual lower-limb in a prosthetic socket: a survey of the development in the first decade. , 1998, Medical engineering & physics.

[30]  Jason T. Kahle.  Conventional and Hydrostatic Transtibial Interface Comparison , 1999 .

[31]  V. C. Roberts,et al.  Clinical investigation of the pressure and shear stress on the trans-tibial stump with a prosthesis. , 1998, Medical engineering & physics.

[32]  David L. Bourell,et al.  Selective laser sintering of metals and ceramics , 1992 .

[33]  Amanda Joyce Brooks,et al.  Bending Strength Test and Evaluation of a Transtibial Prosthetic Socket Fabricated by Selective Laser Sintering , 2004 .

[34]  Noboru Kikuchi,et al.  TOPOLOGY OPTIMIZATION OF COMPLIANT MECHANISMS USING THE HOMOGENIZATION METHOD , 1998 .

[35]  M. Bendsøe,et al.  Generating optimal topologies in structural design using a homogenization method , 1988 .