Process intensification for post-combustion CO2 capture with chemical absorption: A critical review

The concentration of CO2 in the atmosphere is increasing rapidly. CO2 emissions may have an impact on global climate change. Effective CO2 emission abatement strategies such as carbon capture and storage (CCS) are required to combat this trend. Compared with pre-combustion carbon capture and oxy-fuel carbon capture approaches, post-combustion CO2 capture (PCC) using solvent process is one of the most mature carbon capture technologies. There are two main barriers for the PCC process using solvent to be commercially deployed: (a) high capital cost; (b) high thermal efficiency penalty due to solvent regeneration. Applying process intensification (PI) technology into PCC with solvent process has the potential to significantly reduce capital costs compared with conventional technology using packed columns. This paper intends to evaluate different PI technologies for their suitability in PCC process. The study shows that rotating packed bed (RPB) absorber/stripper has attracted much interest due to its high mass transfer capability. Currently experimental studies on CO2 capture using RPB are based on standalone absorber or stripper. Therefore a schematic process flow diagram of intensified PCC process is proposed so as to motivate other researches for possible optimal design, operation and control. To intensify heat transfer in reboiler, spinning disc technology is recommended. To replace cross heat exchanger in conventional PCC (with packed column) process, printed circuit heat exchanger will be preferred. Solvent selection for conventional PCC process has been studied extensively. However, it needs more studies for solvent selection in intensified PCC process. The authors also predicted research challenges in intensified PCC process and potential new breakthrough from different aspects.

[1]  Hallvard F. Svendsen,et al.  Mass transfer and kinetics of carbon dioxide absorption into loaded aqueous monoethanolamine solutions , 2015 .

[2]  Finn Andrew Tobiesen,et al.  Study of a Modified Amine-Based Regeneration Unit , 2006 .

[3]  The enhancement of the rate of absorption of CO2 in amine solutions due to the Marangoni effect , 1997 .

[4]  P. Chiueh,et al.  Microwave pyrolysis of rice straw to produce biochar as an adsorbent for CO2 capture , 2015 .

[5]  Colin Ramshaw,et al.  Evaluation of a Spinning Disc Reactor for Continuous Processing1 , 2001 .

[6]  J. J. Pis,et al.  A comparison of two methods for producing CO 2 capture adsorbents , 2009 .

[7]  Bert Metz,et al.  Carbon Dioxide Capture and Storage , 2005 .

[8]  M. O. Garg,et al.  Carbon Di-Oxide Removal with Mesoporous Adsorbents in a Single Column Pressure Swing Adsorber , 2009 .

[9]  Richard S.H. Mah,et al.  MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS , 1985 .

[10]  Norbert Kockmann,et al.  Industrial design, scale-up, and use of microreactors , 2009 .

[11]  Chung-Sung Tan,et al.  Removal of CO2 from indoor air by alkanolamine in a rotating packed bed , 2011 .

[12]  Brian Stöver,et al.  Optimized post combustion carbon capturing on coal fired power plants , 2011 .

[13]  Nitin Kaistha,et al.  Limiting Gas Liquid Flows and Mass Transfer in a Novel Rotating Packed Bed (HiGee) , 2011 .

[14]  Robin Irons,et al.  Materials challenges for the development of solid sorbents for post-combustion carbon capture , 2012 .

[15]  Rajamani Krishna,et al.  A comparison of the CO2 capture characteristics of zeolites and metal-organic frameworks , 2012 .

[16]  R. Stuart Haszeldine,et al.  Carbon Capture and Storage: How Green Can Black Be? , 2009, Science.

[17]  Ludovic Raynal,et al.  Use of CFD for CO2 absorbers optimum design : from local scale to large industrial scale , 2009 .

[18]  R. L. Pierres,et al.  Heat Exchangers for the Next Generation of Nuclear Reactors , 2006 .

[19]  Pushpam Kumar.  Agriculture (Chapter8) in IPCC, 2007: Climate change 2007: Mitigation of Climate Change. Contribution of Working Group III to the Fourth assessment Report of the Intergovernmental Panel on Climate Change , 2007 .

[20]  R. Balasubramanian,et al.  Biomass derived low-cost microporous adsorbents for efficient CO2 capture , 2015 .

[21]  Kamelia Boodhoo,et al.  Process intensification: spinning disk reactor for styrene polymerisation , 2000 .

[22]  Chung-Sung Tan,et al.  Reduction of CO2 concentration in a zinc/air battery by absorption in a rotating packed bed , 2006 .

[23]  Guang Q. Wang,et al.  Progress on Higee distillation—Introduction to a new device and its industrial applications , 2011 .

[24]  Jianfeng Chen,et al.  Gas–Liquid Effective Interfacial Area in a Rotating Packed Bed , 2012 .

[25]  Nilay Shah,et al.  Dynamic modelling and analysis of an amine-based post-combustion CO2 capture absorption column , 2013 .

[26]  Chia-Chang Lin,et al.  Packing Characteristics for Mass Transfer in a Rotating Packed Bed , 2006 .

[27]  Chung-Sung Tan,et al.  CO2 capture from hot stove gas in steel making process , 2010 .

[28]  Hans Hasse,et al.  Pilot plant experiments for post combustion carbon dioxide capture by reactive absorption with novel solvents , 2011 .

[29]  N. Kolev,et al.  On the evaluation of the interfacial turbulence (the Marangoni effect) in gas (vapour)—liquid mass transfer , 1991 .

[30]  Y. Kato,et al.  Printed circuit heat exchanger thermal–hydraulic performance in supercritical CO2 experimental loop , 2006 .

[31]  Li Wei,et al.  Development of a pentaethylenehexamine-modified solid support adsorbent for CO2 capture from model flue gas , 2015 .

[32]  Chung-Sung Tan,et al.  CO2 capture by piperazine mixed with non-aqueous solvent diethylene glycol in a rotating packed bed , 2013 .

[33]  H. Hasse,et al.  Pilot plant study of two new solvents for post combustion carbon dioxide capture by reactive absorption and comparison to monoethanolamine , 2011 .

[34]  Lei Shao,et al.  Modeling and experimental studies on absorption of CO2 by Benfield solution in rotating packed bed , 2009 .

[35]  Chung-Sung Tan,et al.  Mixed Alkanolamines with Low Regeneration Energy for CO2 Capture in a Rotating Packed Bed , 2013 .

[36]  Hallvard F. Svendsen,et al.  Solubility of CO2 in 15, 30, 45 and 60 mass% MEA from 40 to 120 °C and model representation using the extended UNIQUAC framework , 2011 .

[37]  David Reay,et al.  The role of process intensification in cutting greenhouse gas emissions , 2008 .

[38]  Chia-Chang Lin,et al.  Carbon Dioxide Absorption into NaOH Solution in a Cross-flow Rotating Packed Bed , 2007 .

[39]  A. Morawski,et al.  Alkali-treated titanium dioxide as adsorbent for CO2 capture from air , 2015 .

[40]  Peter Stephenson,et al.  Dynamic Modeling and Simulation of CO2 Chemical Absorption Process for Coal-Fired Power Plants , 2009 .

[41]  Meihong Wang,et al.  Dynamic Validation of Model for Post-Combustion Chemical Absorption CO2 Capture Plant , 2012 .

[42]  Roda Bounaceur,et al.  Membrane processes for post-combustion carbon dioxide capture: A parametric study , 2006 .

[43]  M. V. Gil,et al.  Response surface methodology as an efficient tool for optimizing carbon adsorbents for CO2 capture , 2013 .

[44]  Nilay Shah,et al.  Optimisation of Post-combustion CO2 Capture for Flexible Operation , 2014 .

[45]  Roland Kalb,et al.  Ionic liquids for post-combustion CO2 absorption , 2010 .

[46]  Nitin Kaistha,et al.  Process Intensification in HiGee Absorption and Distillation: Design Procedure and Applications , 2010 .

[47]  Qingling Liu,et al.  Adsorption kinetics for CO2 on highly selective zeolites NaKA and nano-NaKA , 2013 .

[48]  Howard J. Herzog,et al.  Rethinking CCS – Moving Forward in Times of Uncertainty , 2013 .

[49]  Yu-Shao Chen,et al.  Correlations of Mass Transfer Coefficients in a Rotating Packed Bed , 2011 .

[50]  Chia-Chang Lin,et al.  Mass transfer in a rotating packed bed with various radii of the bed , 2005 .

[51]  Xiaofei Zeng,et al.  Absorption of Carbon Dioxide with Ionic Liquid in a Rotating Packed Bed Contactor: Mass Transfer Study , 2011 .

[52]  Colin E. Snape,et al.  Capturing CO 2 from ambient air using a polyethyleneimine – silica adsorbent in fl uidized beds , 2014 .

[53]  Colin Ramshaw,et al.  Process intensification: operating characteristics of rotating packed beds - determination of liquid hold-up for a high-voidage structured packing , 2000 .

[54]  Olav Bolland,et al.  Comparison of solvents for post-combustion capture of CO2 by chemical absorption , 2009 .

[55]  G. T. Polley,et al.  Shortcut Design Approach for Spiral Heat Exchangers , 2007 .

[56]  Chia-Chang Lin,et al.  Carbon dioxide absorption in a cross-flow rotating packed bed , 2011 .

[57]  Hiroshi Takeuchi,et al.  GAS ABSORPTION WITH CHEMICAL REACTION IN PACKED COLUMNS , 1968 .

[58]  Yasuyoshi Kato,et al.  High performance printed circuit heat exchanger , 2007 .

[59]  Xudong Zhao,et al.  Preliminary study of the performance and operating characteristics of a mop-fan air cleaning system for buildings , 2007 .

[60]  Jae Eun Cha,et al.  Numerical investigation on thermal–hydraulic performance of new printed circuit heat exchanger model ☆ , 2008 .

[61]  Colin E. Snape,et al.  Performance of polyethyleneimine–silica adsorbent for post-combustion CO2 capture in a bubbling fluidized bed , 2014 .

[62]  van der J John Schaaf,et al.  Gas-liquid mass transfer in a rotor-stator spinning disc reactor , 2010 .

[63]  J. J. Pis,et al.  Post-combustion CO2 capture adsorbents from spent coffee grounds , 2013 .

[64]  Yong Luo,et al.  Characteristics of a two-stage counter-current rotating packed bed for continuous distillation , 2012 .

[65]  C. H. Phillips.  DEVELOPMENT OF A NOVEL INTEGRATED CHEMICAL REACTOR-HEAT EXCHANGER , 1999 .

[66]  Chia-Chang Lin,et al.  Volatile organic compounds absorption in a cross-flow rotating packed bed. , 2008, Environmental science & technology.

[67]  D. Wagener,et al.  Carbon dioxide capture with concentrated, aqueous piperazine , 2009 .

[68]  A. Mohamed,et al.  A novel (Zr–Ce) incorporated Ca(OH)2 nanostructure as a durable adsorbent for CO2 capture , 2014 .

[69]  Li Zhao,et al.  Multi-stage gas separation membrane processes used in post-combustion capture: Energetic and economic analyses , 2010 .

[70]  A. Beenackers,et al.  Influence of the ejector configuration, scale and the gas density on the mass transfer characteristics of gas-liquid ejectors , 2001 .

[71]  Milorad P. Dudukovic,et al.  Mass-transfer in rotating packed beds—II. Experimental results and comparison with theory and gravity flow , 1989 .

[72]  Christian Bergins,et al.  TECHNOLOGY OPTIONS FOR CLEAN COAL POWER GENERATION WITH CO 2 CAPTURE , 2010 .

[73]  Hans Hasse,et al.  Pilot plant experimental studies of post combustion CO2 capture by reactive absorption with MEA and new solvents , 2009 .

[74]  Jon Gibbins,et al.  Scope for reductions in the cost of CO2 capture using flue gas scrubbing with amine solvents , 2004 .

[75]  David Reay,et al.  Compact Heat Exchangers: Selection, Design and Operation , 2001 .

[76]  Colin Ramshaw,et al.  Carbon dioxide absorption and desorption in aqueous monoethanolamine solutions in a rotating packed bed , 2007 .

[77]  Francis Meunier,et al.  Numerical parametric study on CO2 capture by indirect thermal swing adsorption , 2011 .

[78]  Chia-Chang Lin,et al.  Removal of carbon dioxide by absorption in a rotating packed bed , 2003 .

[80]  G. Astarita,et al.  Carbon dioxide absorption in aqueous monoethanolamine solutions , 1961 .

[81]  Enrico Drioli,et al.  Membrane Gas Separation: A Review/State of the Art , 2009 .

[82]  Qi Li,et al.  Compact heat exchangers: A review and future applications for a new generation of high temperature solar receivers , 2011 .

[83]  Mohamed Rashid Al Rashid,et al.  Carbon dioxide capture from Flue gases , 2016 .

[84]  J. Gibbins,et al.  Valuing Responsive Operation of Post-combustion CCS Power Plants in Low Carbon Electricity Markets , 2014 .

[85]  Hanne M. Kvamsdal,et al.  Flue-gas cooling in post-combustion capture plants , 2011 .

[86]  Jon Gibbins,et al.  On the integration of CO2 capture with coal-fired power plants: A methodology to assess and optimise solvent-based post-combustion capture systems , 2011 .

[87]  Chia-Chang Lin,et al.  Research Articles : Carbon Dioxide Absorption into NaOH Solution in a Cross-flow Rotating Packed Bed , 2007 .

[88]  Ludovic Raynal,et al.  A multi-scale approach for CFD calculations of gas–liquid flow within large size column equipped with structured packing , 2007 .

[89]  Meihong Wang,et al.  Dynamic modelling of CO2 absorption for post combustion capture in coal-fired power plants , 2009 .

[90]  Nilay Shah,et al.  Dynamic modelling and analysis of a coal-fired power plant integrated with a novel split-flow configuration post-combustion CO2 capture process , 2014 .

[91]  Xiuqing Li,et al.  Alloy 617 for the High Temperature Diffusion-Bonded Compact Heat Exchangers , 2008 .

[92]  Chung-Sung Tan,et al.  Carbon dioxide capture by blended alkanolamines in rotating packed bed , 2009 .

[93]  Kaimin Li,et al.  The influence of polyethyleneimine type and molecular weight on the CO2 capture performance of PEI-nano silica adsorbents , 2014 .

[94]  C. Ramshaw,et al.  Process analysis of intensified absorber for post-combustion CO2 capture through modelling and simulation , 2014 .

[95]  Jianfeng Chen,et al.  Computational fluid dynamic simulation of fluid flow in a rotating packed bed , 2010 .

[96]  Chung-Sung Tan,et al.  Absorption of carbon dioxide with piperazine and its mixtures in a rotating packed bed , 2006 .

[97]  Lin Ma,et al.  A Semi-Empirical Model for Estimating the Heat Capacity of Aqueous Solutions of Alkanolamines for CO2 Capture , 2014 .

[98]  Hwai-Shen Liu,et al.  Mass Transfer in a Rotating Packed Bed with Viscous Newtonian and Non-Newtonian Fluids , 2005 .

[99]  Guang Q. Wang,et al.  Performance of a rotating zigzag bed—A new HIGEE , 2008 .

[100]  Aarti,et al.  CO2 recovery from mixtures with nitrogen in a vacuum swing adsorber using metal organic framework adsorbent: A comparative study , 2012 .

[101]  Kamelia Boodhoo,et al.  An evaluation of the effectiveness of continuous thin film processing in a spinning disc reactor for bulk free-radical photo-copolymerisation , 2013 .

[102]  Karl Stéphenne,et al.  Start-up of World's First Commercial Post-combustion Coal Fired CCS Project: Contribution of Shell Cansolv to SaskPower Boundary Dam ICCS Project , 2014 .

[103]  D. P. Sekulic,et al.  Fundamentals of Heat Exchanger Design , 2003 .

[104]  Hanne M. Kvamsdal,et al.  Maintaining a neutral water balance in a 450 MWe NGCC-CCS power system with post-combustion carbon dioxide capture aimed at offshore operation , 2010 .

[105]  Jc Jaap Schouten,et al.  Liquid-solid mass transfer and reaction in a rotor-stator spinning disc reactor , 2010 .

[106]  N. Shah,et al.  The multi-period optimisation of an amine-based CO2 capture process integrated with a super-critical coal-fired power station for flexible operation , 2015, Comput. Chem. Eng..

[107]  Kazuya Goto,et al.  A review of efficiency penalty in a coal-fired power plant with post-combustion CO2 capture , 2013 .

[108]  Wilfredo Yave,et al.  PEG modified poly(amide-b-ethylene oxide) membranes for CO2 separation , 2008 .

[109]  Jc Jaap Schouten,et al.  Mass transfer in a rotor-stator spinning disc reactor with cofeeding of gas and liquid , 2010 .

[110]  Aie.  Energy Efficiency Indicators for Public Electricity Production from Fossil Fuels , 2009 .

[111]  B. Metz.  IPCC special report on carbon dioxide capture and storage , 2005 .

[112]  Chia-Chang Lin,et al.  Micromixing in a Rotating Packed Bed , 2004 .

[113]  H. Herzog,et al.  Scaling up carbon dioxide capture and storage: From megatons to gigatons , 2011 .

[114]  Patricia Luis,et al.  Carbon dioxide capture from flue gases using a cross-flow membrane contactor and the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate , 2010 .

[115]  Meihong Wang,et al.  Modelling and simulation of intensified absorber for post-combustion CO2 capture using different mass transfer correlations , 2015 .

[116]  Alfons Kather,et al.  Semi-empirical model for the direct simulation of power plant with integrated post-combustion CO2 capture processes by wet chemical absorption , 2011 .

[117]  Ming Zhao,et al.  A review of techno-economic models for the retrofitting of conventional pulverised-coal power plants for post-combustion capture (PCC) of CO2 , 2013 .

[118]  H. E. Benson,et al.  CO/sub 2/ absorption: employing hot potassium carbonate solutions , 1954 .

[119]  Henry W. Pennline,et al.  Aqua ammonia process for simultaneous removal of CO2, SO2 and NOx , 2004 .

[120]  Guang Q. Wang,et al.  New HIGEE-Rotating Zigzag Bed and Its Mass Transfer Performance , 2008 .

[121]  Chia-Chang Lin,et al.  Performance of a cross-flow rotating packed bed in removing carbon dioxide from gaseous streams by chemical absorption , 2011 .

[122]  Marta G. Plaza,et al.  Sustainable biomass-based carbon adsorbents for post-combustion CO2 capture , 2013 .

[123]  P. Freund,et al.  Making deep reductions in CO2 emissions from coal-fired power plant using capture and storage of CO2 , 2003 .

[124]  David Reay.  Learning from Experiences with Compact Heat Exchangers , 1999 .

[125]  Lin Ma,et al.  Optimal Process Design of Commercial-Scale Amine-Based CO2 Capture Plants , 2014 .

[126]  Peter Folger,et al.  Carbon Capture: A Technology Assessment , 2013 .

[127]  Niall Mac Dowell,et al.  Enhanced Operating Flexibility and Optimised Off-design Operation of Coal Plants with Post-combustion Capture , 2014 .

[128]  Masaki Iijima,et al.  Development of energy saving technology for flue gas carbon dioxide recovery in power plant by chemical absorption method and steam system , 1997 .

[129]  G. Versteeg,et al.  CO2 capture from power plants. Part I: A parametric study of the technical performance based on monoethanolamine , 2007 .

[130]  N. Cai,et al.  Effect of K2CO3·1.5H2O on the regeneration energy consumption of potassium-based sorbents for CO2 capture , 2013 .

[131]  L. Scriven,et al.  Interfacial turbulence: Hydrodynamic instability and the marangoni effect , 1959 .

[132]  Jinyue Yan,et al.  Adsorbents for the post-combustion capture of CO2 using rapid temperature swing or vacuum swing adsorption , 2013 .

[133]  Reinhard Menzer,et al.  Concepts and investment cost analyses of multi-stage membrane systems used in post-combustion processes , 2009 .

[134]  Enrico Drioli,et al.  Membrane technologies for CO2 separation , 2010 .

[135]  Tomio Mimura,et al.  Research and development on energy saving technology for flue gas carbon dioxide recovery and steam system in power plant , 1995 .

[136]  Takuya Hirata,et al.  Current status of MHI’s CO2 recovery technology and optimization of CO2 recovery plant with a PC fired power plant , 2009 .

[137]  Seung Ju Han,et al.  Synthesis of a dual-templated MgO–Al2O3 adsorbent using block copolymer and ionic liquid for CO2 capture , 2015 .

[138]  Meihong Wang,et al.  Demonstrating full-scale post-combustion CO2 capture for coal-fired power plants through dynamic modelling and simulation , 2012 .

[139]  M. Sander,et al.  The Fluor Daniel® econamine FG process: Past experience and present day focus , 1992 .

[140]  R. M. Machado,et al.  Developments in hydrogenation technology for fine-chemical and pharmaceutical applications. , 2001, Current opinion in drug discovery & development.

[141]  Chung-Sung Tan,et al.  CO2 capture by alkanolamine solutions containing diethylenetriamine and piperazine in a rotating packed bed , 2012 .

[142]  Hans Hasse,et al.  Pilot plant study of four new solvents for post combustion carbon dioxide capture by reactive absorption and comparison to MEA , 2012 .

[143]  N. Kockmann,et al.  Microreactor Technology and Continuous Processes in the Fine Chemical and Pharmaceutical Industry: Is the Revolution Underway? , 2008 .

[144]  S. Gu,et al.  3D modeling of hydrodynamics and physical mass transfer characteristics of liquid film flows in structured packing elements , 2013 .

[145]  B. Arias,et al.  Emerging CO2 capture systems , 2015 .

[146]  Carolina Font Palma,et al.  Experimental and Process Modelling Study of Integration of a Micro-turbine with an Amine Plant , 2014 .

[147]  Chung-Sung Tan,et al.  Thermal regeneration of alkanolamine solutions in a rotating packed bed , 2013 .

[148]  Paul A. Webley,et al.  A new simplified pressure/vacuum swing adsorption model for rapid adsorbent screening for CO2 capture applications , 2013 .

[149]  S. Drobniak,et al.  CFD Modelling of CO2 Capture in a Packed Bed by Chemical Absorption , 2013 .

[150]  Devin Shaw,et al.  Cansolv CO2 capture: The value of integration , 2009 .

[151]  Gary T. Rochelle,et al.  Absorption of carbon dioxide into aqueous piperazine: reaction kinetics, mass transfer and solubility , 2000 .

[152]  Jianfeng Chen,et al.  CFD analysis of liquid phase flow in a rotating packed bed reactor , 2013 .

[153]  H. Yeung,et al.  Dynamic modelling and analysis of post-combustion CO2 chemical absorption process for coal-fired power plants , 2010 .

[154]  Chaodi Xu,et al.  Microporous adsorbents for CO2 capture - a case for microporous polymers? , 2014 .

[155]  Gary T. Rochelle,et al.  Effects of the Temperature Bulge in CO2 Absorption from Flue Gas by Aqueous Monoethanolamine , 2008 .

[156]  H. M. Kvamsdal,et al.  Dynamic modeling and simulation of a CO2 absorber column for post-combustion CO2 capture , 2009 .

[157]  Ki-Hyun Kim,et al.  A comparative review between amines and ammonia as sorptive media for post-combustion CO2 capture , 2015 .

[158]  Eric Favre,et al.  Carbon dioxide recovery from post-combustion processes: Can gas permeation membranes compete with absorption? , 2007 .

[159]  H. Pfeiffer,et al.  Potassium-based sorbents using mesostructured γ-alumina supports for low temperature CO2 capture , 2015 .

[160]  Chia-Chang Lin,et al.  Evaluation of alkanolamine solutions for carbon dioxide removal in cross-flow rotating packed beds. , 2010, Journal of hazardous materials.

[161]  Chih-Hung Huang,et al.  A Review of CO2 Capture by Absorption and Adsorption , 2012 .

[162]  A. Samanta,et al.  Post-Combustion CO2 Capture Using Solid Sorbents: A Review , 2012 .

[163]  Gary T. Rochelle,et al.  Absorption and desorption rates of carbon dioxide with monoethanolamine and piperazine , 2009 .