Reduction of Fan and Compressor Wake Defect Using Plasma Actuation for Tonal Noise Reduction

This paper proposes a new technique to reduce the noise generated by rotor-stator interaction (tonal noise) in fans and compressors. The method involves the use of single dielectric barrier discharge (plasma) actuators near the blade trailing edge to reduce blade wakes. Plasma actuators are a new and simple type of active flow control device consisting of two parallel and offset electrodes separated by a layer of dielectric material. The application of a high ac voltage at high frequency to the electrodes generates a body force on the flow in the vicinity of the electrodes to inject momentum without mass addition. A preliminary assessment of the proposed concept is performed with a computational study on modern low-speed compressor rotor geometry. A plasma actuator model is implemented in an established turbomachinery CFD code. Simulations are carried out to evaluate the effect of the actuator strength, location, and actuation method (continuous versus pulsed) on the rotor wake. Results show that plasma actuators operated in continuous mode near the trailing edge can significantly influence the wake of the rotor with relatively little power consumption. The effectiveness of the actuation is proportional to actuator strength (induced body force). The exact position of the actuator in the trailing edge region has little effect on the effectiveness of the actuation. The results from simulations with pulsed actuation show very low time-averaged influence on the wake and are not fully conclusive, due possibly to the frequencies simulated and the limitations of the RANS CFD tool.

[1]  Wei Shyy,et al.  Modeling of dielectric barrier discharge and resulting fluid dynamics , 2006 .

[2]  T. McLaughlin,et al.  Mechanisms and Responses of a Single Dielectric Barrier Plasma , 2003 .

[3]  Miguel R. Visbal,et al.  Effective Discharge Dynamics for Plasma Actuators , 2006 .

[4]  Chih-Ming Ho,et al.  Subharmonics and vortex merging in mixing layers , 1982, Journal of Fluid Mechanics.

[5]  John M. Brookfield.  Turbofan rotor/stator interaction noise reduction through trailing edge blowing , 1998 .

[6]  Huu Duc Vo.  Suppression of Short Length-Scale Rotating Stall Inception With Glow Discharge Actuation , 2007 .

[7]  Dmitriy M. Orlov,et al.  Modelling and simulation of single dielectric barrier discharge plasma actuators , 2006 .

[8]  Thomas Corke,et al.  Numerical Simulation of Aerodynamic Plasma Actuator Effects , 2005 .

[9]  Eric J. Jumper,et al.  Potential Flow Model for Plasma Actuation as a Lift Enhancement Device , 2005 .

[10]  M. Visbal,et al.  Simulation of Plasma-Based Flow-Control Strategies for Transitional Highly-Loaded Low-Pressure Turbines , 2007 .

[11]  Wake Filling Techniques for Reducing Rotor-Stator Interaction Noise , 2005 .

[12]  Gabriel Font,et al.  Boundary Layer Control with Atmospheric Plasma Discharge , 2004 .

[13]  T. Corke,et al.  Separation Control on HIgh Angle of Attack Airfoil Using Plasma Actuators , 2004 .

[14]  C. L. Enloe,et al.  Simulation of the Effects of Force and Heat Produced by a Plasma Actuator on Neutral Flow Evolution , 2006 .

[15]  Thomas McLaughlin,et al.  Momentum Transfer for an Aerodynamic Plasma Actuator with an Imposed Boundary Layer , 2006 .

[16]  Wei Shyy,et al.  Modeling of glow discharge-induced fluid dynamics , 2002 .

[17]  Gabriel Font,et al.  Boundary Layer Control with Atmospheric Plasma Discharges , 2006 .

[18]  A. Kozlov,et al.  Plasma actuators for bluff body flow control , 2006 .

[19]  Edmane Envia,et al.  Fan Noise Reduction: An Overview , 2002 .

[20]  Miguel R. Visbal,et al.  A Coupled Approach for Plasma-Based Flow Control Simulations of Wing Sections , 2006 .

[21]  H. Schlichting.  Boundary Layer Theory , 1955 .

[22]  Thomas McLaughlin,et al.  Using Plasma Actuators Flaps to Control Laminar Separation on Turbine Blades in a Linear Cascade , 2003 .

[23]  Scott C. Morris,et al.  Tip Clearance Control Using Plasma Actuators , 2005 .

[24]  Thomas Apker,et al.  Modeling and Experiment of Leading Edge Separation Control Using SDBD Plasma Actuators , 2007 .

[25]  Jamey Jacob,et al.  Numerical Simulations of Plasma Based Flow Control Applications , 2005 .

[26]  William N. Dawes,et al.  Compressor rotor wakes and tone noise study , 2003 .

[27]  T. McLaughlin,et al.  Temporal Force Measurements on an Aerodynamic Plasma Actuator , 2006 .

[28]  J. D. Denton,et al.  The Use of a Distributed Body Force to Simulate Viscous Effects in 3D Flow Calculations , 1986 .

[29]  Subrata Roy,et al.  Modeling Surface Discharge Effects of Atmospheric RF on Gas Flow Control , 2005 .

[30]  Gabriele Neretti,et al.  Experimental Investigation of DBD Plasma Actuators Driven by Repetitive High Voltage Nanosecond Pulses with DC or Low-Frequency Sinusoidal Bias , 2007 .

[31]  J. Anderson,et al.  Fundamentals of Aerodynamics , 1984 .

[32]  Junhui Huang,et al.  Separation Control over Low Pressure Turbine Blades Using Plasma Actuators , 2005 .

[33]  T. G. Sofrin,et al.  Axial Flow Compressor Noise Studies , 1962 .

[34]  Christopher Halasz.  Advanced Trailing Edge Blowing Concepts for Fan Noise Control: Experimental Validation , 2005 .

[35]  E. Matlis,et al.  Controlled Experiments on Instabilities and Transition to Turbulence on a Sharp Cone at Mach 3.5 , 2003 .

[36]  Thomas C. Corke,et al.  Overview of Plasma Flow Control: Concepts, Optimization, and Applications , 2005 .

[37]  Sarah Tweedie,et al.  Experimental Investigation of Flow Control Techniques To Reduce Hydroacoustic Rotor-Stator Interaction Noise , 2006 .

[38]  Chih-Ming Ho,et al.  Perturbed Free Shear Layers , 1984 .

[39]  R. Miles,et al.  Numerical modeling of DBD plasma actuators and the induced air flow. , 2007 .

[40]  Thomas Corke,et al.  Plasma Actuators for Separation Control of Low-Pressure Turbine Blades , 2006 .

[41]  Edmane. Envia,et al.  Influence of vane sweep on rotor-stator interaction noise , 1988 .

[42]  Ian A. Waitz,et al.  Trailing-Edge Blowing for Reduction of Turbomachinery Fan Noise , 2000 .